Search found 228 matches

by dr.occa
Fri Feb 15, 2013 10:56 pm
Forum: Powered by Megajolt Gallery
Topic: Datsun 240z with L28 & 3x 40 DCOE, MJLJ w/ TPS
Replies: 34
Views: 83506

I love your TPS mount! Simple but effective!
by dr.occa
Tue Dec 04, 2012 5:32 pm
Forum: Installation
Topic: Big block mopar mega jolt hellllllp !!!!
Replies: 2
Views: 8600

With your Engine at TDC (and you facing the front of it looking at the face of the motor) your 36-1 trigger wheel should be mounted on your crank to where the VR sensor is directly above the 5th tooth to the left of the missing tooth.
by dr.occa
Sat Nov 03, 2012 12:21 pm
Forum: Installation
Topic: New install holding back missfire
Replies: 19
Views: 36027

I know the hill climb took place over 2 months ago - how did it go? How did the engine perform?

Also, could we get some pics of the car and install?
by dr.occa
Mon Oct 01, 2012 5:59 pm
Forum: Operation
Topic: Erraneous tach output in a high rev engine load condition?
Replies: 2
Views: 7768

This link might help as well as this one.
by dr.occa
Mon Oct 01, 2012 5:33 pm
Forum: General Discussion
Topic: Help
Replies: 2
Views: 8228

Did you make certain that your plug wires are plugged to the coil pack properly?

1&4 fire together
2&3 fire together
by dr.occa
Thu Aug 30, 2012 6:29 pm
Forum: Q&A
Topic: a little help for a newbie?
Replies: 3
Views: 10600

Reference the image below for the appropriate pin outs. Don't go by the wire coloring. That can be arbitrary.

Notice the key ways on the diagram; they'll indicate which is your no. 1 pin out for your PIP signal.
Image
by dr.occa
Tue Aug 28, 2012 1:11 pm
Forum: Q&A
Topic: a little help for a newbie?
Replies: 3
Views: 10600

here's what you've got: -edis 4 -pick up (vr sensor) -coil pack -wiring connectors (for edis, pickup & coil pack?) what you say you need now: -megajolt (you can order one for either TPS <-you'll need to obtain a TPS or MAP <-for this it will already have the MAP sensor) -36:1 trigger wheel -brac...
by dr.occa
Fri Aug 17, 2012 7:22 pm
Forum: Q&A
Topic: rotary megajolt
Replies: 27
Views: 64447

I believe this should work. It would require the following: 2x EDIS-4 modules 2x VR Sensors 2x Megajolt Lite Jr 1x 4 post coil pack Pin 12 of both EDIS modules just wouldn't be used because the coil for 2 & 3 on a 4 cylinder can't be programmed to spark 20° behind the leading coil even with a se...
by dr.occa
Tue Aug 14, 2012 12:29 pm
Forum: Q&A
Topic: rotary megajolt
Replies: 27
Views: 64447

Sorry to bring this back up nearly 2 years later. I've got my 12A project up and running and wanted to re-visit this. Proper timing for my Wankel as per the FSM is ATDC Lead 1 should be 0° while Trail 1 should be 20° ATDC. There should be no advance at 500rpm but at least 10° of advance at 1500rpm o...
by dr.occa
Mon Aug 13, 2012 9:25 pm
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 643270

With lesser teeth I don't see why not at those diameters. According to my first gen rx7 fsm, the leading ignition timing at 500rpm idle is 0° while the trailing should be at 10°. Sooo, if there were 2 36-1 trigger wheels on the rotary eccentric shaft pulley with say the rear wheel staggered by a sin...
by dr.occa
Fri Aug 10, 2012 9:21 pm
Forum: Powered by Megajolt Gallery
Topic: The POS makes it's presents felt...
Replies: 29
Views: 79501

I hope to have my Wankel running a draw through setup eventually AND energized by MJLJ.
by dr.occa
Fri Aug 10, 2012 9:19 pm
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 643270

Let me know if you need anything. I spent alot of "quality time" LOL messing with that to get it to work corectly. At some point I would like to see just how small a trigger wheel it would work with. You would start losing definition Dean UNLESS the pickup/VR sensor used a something like ...
by dr.occa
Fri Aug 10, 2012 9:01 pm
Forum: Future Upgrades
Topic: Megajolt Android tuning app
Replies: 104
Views: 2196137

capri_turbo wrote:Is this project still happening?
+1
by dr.occa
Thu Mar 22, 2012 3:48 am
Forum: Powered by Megajolt Gallery
Topic: Work in Progress 1973 240z L28 Blowthrough Turbo Project
Replies: 7
Views: 27100

I love solex/mikunis! That's boss that you have the old school HKS turbo manifold for the L28!
by dr.occa
Thu Mar 22, 2012 3:42 am
Forum: News and Announcements
Topic: Original Ford EDIS module firmware engineer
Replies: 1
Views: 11422

Re: Original Ford EDIS module firmware engineer

This is *very interesting* I just found out who originally wrote the firmware code for the Ford EDIS module. I will likely be able to spend some time with him. Need to write up my burning questions and buy him some dinner & drinks! :) Pester him for a Q&A for the MJLJ community Brent! On an...