Search found 91 matches

by Ken555
Tue Mar 22, 2011 7:41 pm
Forum: News and Announcements
Topic: Babypixie
Replies: 13
Views: 15307

Congratulations :D

Our son Marcus Alexander was born 1/12/2010 weighing 7lbs 14oz
by Ken555
Thu Jan 06, 2011 1:50 pm
Forum: Installation
Topic: What tools to remove EDIS from scrap vehicle?
Replies: 4
Views: 3942

Battery Angle Grinder, is what I used! :oops: You might find the screws have rusted into place, I just cut around the mounts, and ground the head off the crank sensor as I remember it being a Torx. Depends on the scrap yard policy on damaging other components, mine doesn't care. I watched people wit...
by Ken555
Thu Nov 25, 2010 9:51 am
Forum: News and Announcements
Topic: Babypixie
Replies: 13
Views: 15307

Well done.

We're less that 2 weeks away from the due date for our first.

Great timing, seeing as we currently have several inches of snow on the roads.
by Ken555
Tue Sep 21, 2010 9:13 pm
Forum: New Project Suggestions
Topic: New projects teaser.
Replies: 7
Views: 9957

Re: New projects teaser.

brentp wrote:Received some brand new board designs today. Can you guess what they're for? One should be easy..
Well going from the names, Launch control, Interceptor -> Canbus interface ?, Race Capture, Injectx -> Fuel injection controller -> Megasquirt style.
by Ken555
Sun Sep 05, 2010 6:12 pm
Forum: Installation
Topic: Shields, earths, help please!
Replies: 6
Views: 5711

I run the set up in the diagram (It was me that posted it originally) for quite a while, with no problems. I later fitted one of the Beta test rev limiter and modified it to power the coil pack from the MJ unit. But still the earths are wired as shown, the actual connection is a ring terminal betwee...
by Ken555
Tue Apr 06, 2010 12:55 pm
Forum: Installation
Topic: Trigger Wheel, shrink fit vs. bolting/welding?
Replies: 5
Views: 6261

I fitted my trigger wheel in the same way, well apart from Liquid nitrogen as a coolant. They also machined on a slight taper to the crank pulley and trigger wheel (you can't see it by eye), this means that when fitted you would need it to expand to come loose. The original Sierra wheel is fitted th...
by Ken555
Fri Mar 19, 2010 11:05 am
Forum: General Discussion
Topic: Autosportlabs Meet UK
Replies: 30
Views: 28191

You could also catch this the next day nearby.
Thats where I will be.

Image
by Ken555
Tue Feb 23, 2010 10:06 pm
Forum: Installation
Topic: Spark plugs??
Replies: 2
Views: 2553

You most definitely need resistor plugs, see the problems I had here
http://www.autosportlabs.org/viewtopic. ... ght=#12192

I have NKG BRP6ES the alternative is Champion RN9YCC
by Ken555
Mon Feb 08, 2010 11:15 am
Forum: Installation
Topic: Trigger Wheel & PIckup Install A-Series
Replies: 9
Views: 7551

Knew I had seen that type of setup before somewhere.

So the 2nd diagram is correct. Here's a photo of the assembly

So its sensor/bracket/plate
The sensor can be spaced backwards with a washer if needed.

Image
by Ken555
Mon Feb 08, 2010 11:05 am
Forum: Installation
Topic: Trigger Wheel & PIckup Install A-Series
Replies: 9
Views: 7551

Or if thats too far forward try this way
by Ken555
Mon Feb 08, 2010 10:57 am
Forum: Installation
Topic: Trigger Wheel & PIckup Install A-Series
Replies: 9
Views: 7551

I would say its a clamp to spread the pressure of the bolt.

So it goes like the poor Paint picture attached
by Ken555
Sun Feb 07, 2010 9:13 pm
Forum: Installation
Topic: Trigger Wheel & PIckup Install A-Series
Replies: 9
Views: 7551

Image

How close mine is
by Ken555
Sun Feb 07, 2010 9:10 pm
Forum: Installation
Topic: Trigger Wheel & PIckup Install A-Series
Replies: 9
Views: 7551

I would say that's miles too far away.

I set mine with a feeler gauge at 1/64 of an inch approx 0.5mm

Can it be mounted the otherside of the bracket ?
by Ken555
Tue Feb 02, 2010 7:18 pm
Forum: General Discussion
Topic: Top ten on Autosportlabs
Replies: 6
Views: 7554

Seems I make the top 20.

In at number 14
by Ken555
Fri Dec 04, 2009 6:31 pm
Forum: Installation
Topic: Sequential shift lights
Replies: 11
Views: 7160

There is no cover, just drilled the face of the gauge and mounted behind.