Search found 16 matches

by crossflow
Mon Nov 13, 2017 8:44 am
Forum: Hard Rev Limiter
Topic: Are empty holes OK ?
Replies: 4
Views: 4084

Hi, thanks for your help.
Cornelius
by crossflow
Fri Nov 10, 2017 3:50 pm
Forum: Hard Rev Limiter
Topic: Are empty holes OK ?
Replies: 4
Views: 4084

here is the picture
by crossflow
Wed Nov 08, 2017 10:56 am
Forum: Hard Rev Limiter
Topic: Are empty holes OK ?
Replies: 4
Views: 4084

Are empty holes OK ?

Hi, many, many years ago, I bought a Hard Rev Limiter V 1.2.0. I am about to put it in my only recently purchased MegaJolt. I have read the instructions and I understand that I have to solder 4 wires. Must I soder anything else ? There are still 3 empty holes, marked C, B and E I guess that it is a ...
by crossflow
Tue Sep 30, 2014 9:07 pm
Forum: Operation
Topic: Aftermarket knock sensors
Replies: 9
Views: 14616

@ Oliver

I had a look at the site you mentioned.
There are 4 different products.
Which one have you bought and used ?
by crossflow
Wed Sep 10, 2014 8:07 pm
Forum: Operation
Topic: Aftermarket knock sensors
Replies: 9
Views: 14616

This is not from me, but
I saw some photos here:
www.lathyrus.eu

than click on:
Special tools and parts

than click on:
Knock detection circuit
by crossflow
Sun Jun 22, 2014 10:37 am
Forum: Installation
Topic: Spark plug wiring for a Rover V8
Replies: 11
Views: 15394

Hi,

here is a picture with my installation.
Rover V 8 3.5 in a Triumph TR 7.
I swapped the HT cables until it locked tidy.
As said before, you can swap cables on EACH coil,
not between the coils.

Cornelius
by crossflow
Tue Apr 22, 2014 8:16 am
Forum: Operation
Topic: Question about Flash
Replies: 2
Views: 2889

Thanks, Brent

Cornelius
by crossflow
Sun Feb 16, 2014 2:12 pm
Forum: Operation
Topic: Question about Flash
Replies: 2
Views: 2889

Question about Flash

Hi, I have a MegaJolt V3 and I'm about to put it in my car. EDIS is running already in Limp Home mode. I have some questions about flashing. I have found this and I quote from the Operation guide: "Persisting the data to flash requires a significant amount of time" 1. Is there a message when it is f...
by crossflow
Fri Nov 22, 2013 3:15 pm
Forum: Installation
Topic: Values for fuses recommendation
Replies: 8
Views: 7349

« I don't like to use any more terminals and connectors than absolutely necessary« I totally agree with your statement. I just could leave two slots for the fuses empty. Are the wires all on one side of the parallel crimp splice ? I am confused about crimping and soldering. I am used to crimp or so...
by crossflow
Wed Nov 20, 2013 3:10 pm
Forum: Installation
Topic: Values for fuses recommendation
Replies: 8
Views: 7349

One reason is, I have this nice little holder for the relay. The other reason is, I can distribute easily the power from one point to the four devices. Two coil packs, EDIS module, and MegaJoltBox. How do you connect four wires to one wire ? For earth distribution I will use this: I got this from a ...
by crossflow
Tue Nov 19, 2013 4:13 pm
Forum: Installation
Topic: Values for fuses recommendation
Replies: 8
Views: 7349

Values for fuses recommendation

I'm about to put the MegaJolt EDIS into my car.
I have planned to put some fuses and a relay in.
What values of fuses should I use ?
Please have look at my sketch.
by crossflow
Thu Jan 27, 2011 9:49 am
Forum: Q&A
Topic: What software do I need for megajolt V 3 ???
Replies: 8
Views: 7398

I don't use any USB-Serial Adapter, so no problems there.
Than I wired a switch in the power supply.
That made all the difference.
It worked!
Thanks again Brent.

Cornelius
by crossflow
Wed Jan 26, 2011 12:20 pm
Forum: Q&A
Topic: What software do I need for megajolt V 3 ???
Replies: 8
Views: 7398

Hi Brent, thanks for your answer. Sorry I can't report a success. I followed the steps in the firmware upgrade guide. I got the "Waiting for...." message and than: "received 0xfc (good)" After powering up the unit I got: "Calibration break pulse sent. Count:1 Can't read MCU info. Could be protocol e...
by crossflow
Tue Jan 25, 2011 4:43 pm
Forum: Q&A
Topic: What software do I need for megajolt V 3 ???
Replies: 8
Views: 7398

Hi, I have read this forum a couple of hours. Found an answer somewhere else, saying: you should download V 3.2.1 I did it and connected the MJLJ board. I got a message that this version does not work with my firmeware. So I downloaded and installed version 3.0.0 Now I got the "Could not open port" ...
by crossflow
Sun Jan 23, 2011 12:20 pm
Forum: Q&A
Topic: What software do I need for megajolt V 3 ???
Replies: 8
Views: 7398

Hi Ryan,

thanks for your answer.
I found the following versions:
V3.0.0
V3.1.0
V3.1.1
V3.1.2
V3.2.0
V3.2.1
V3.3.0
V3.3.1
V3.3.2

Which version should I download onto my computer ?

Cornelius