Search found 32 matches

by eds911915
Sun Mar 25, 2018 5:02 pm
Forum: Operation
Topic: cant read load bin
Replies: 1
Views: 5711

cant read load bin

hello autosportlabs. i was able to open the come port by changing the comport settings (very promising) im using a real DB9 serial cable not a USB232 adapter. Anyway this MEGAJOLT was removed out of a running vehicle about 5 years ago and placed on a shelf away from any moisture. so before i hardwir...
by eds911915
Sun Mar 18, 2018 1:34 am
Forum: Operation
Topic: could not open comport
Replies: 1
Views: 5430

could not open comport

hello MegaJolt_its bin awhile since iv bin to the autosport forum anyway iv got a Megajolt/e that i used to use in my 1974 2002 BMW i removed about 4 years ago and put it in a box it was working fine. so today i pulled it off the shelf and loaded all the firmware and drivers powered it up with a 9 v...
by eds911915
Sat Apr 06, 2013 11:41 pm
Forum: Powered by Megajolt Gallery
Topic: 1973 BMW 2002tii
Replies: 1
Views: 13246

ignition map

id like a copy of your ignition map i have 76 2002 with weber 38/38 dgas carb, dr shrick 284, ganeric header, megajolt lite
by eds911915
Sat Apr 06, 2013 4:08 pm
Forum: RaceCapture/Pro General Q&A
Topic: race capture pro question
Replies: 1
Views: 3177

race capture pro question

can it control fuel and spark?
by eds911915
Thu Jan 31, 2013 3:45 am
Forum: Installation
Topic: wiring question
Replies: 1
Views: 3472

wiring question

how can i use megajolt to power up a fuel pump relay. iv got alot of un used pins at the megajolt ecu. is it a bad idea?
by eds911915
Sat Aug 25, 2012 2:36 pm
Forum: Installation
Topic: A-series refusing to start
Replies: 5
Views: 5365

a series cranks but wont start

check for spark befor you do another activity it doesnt matter for the sake of spark wear the wheel is positioned. i think the best way to do is pull all the plugs out so the engine spins free (no load) lay all your plugs on the cam cover (make sure there grounded) crank the motor and you should see...
by eds911915
Sat Aug 25, 2012 1:37 am
Forum: Installation
Topic: how can i simulate a waveform
Replies: 1
Views: 3165

how can i simulate a waveform

could anyone tell me what is the easiest/cheepist way to send a 36-1 vr signal into a EDIS-4 module pins 5&6. i wanna trick the system. iv seen the megasquirt stimulator but i dont fully understand how it works.
by eds911915
Sat Aug 25, 2012 1:32 am
Forum: Installation
Topic: getting a bad waveform
Replies: 2
Views: 4201

getting a bad waveform

the type of driveability im getting is very weak spark. the engine wont run.
by eds911915
Sat Aug 25, 2012 1:28 am
Forum: Installation
Topic: New install holding back missfire
Replies: 19
Views: 36039

miss fire at 4600rpm

thers other things that cuase misfire other then ignition. you should go back to basic engine performance suck- squeeze- bang- blow make sure all the basic stuff is working to spec at 4600rpm.
by eds911915
Wed Jul 25, 2012 3:39 am
Forum: Installation
Topic: getting a bad waveform
Replies: 2
Views: 4201

getting a bad waveform

iv bin comparing the waveform my vr sensor produces to some that people have posted in the archives and mine looks really bad the peaks and vallies are all waded up and i cant see the missing tooth. I cant post it because im using the origanal snap on vantage but it has alot of edis tests loaded in ...
by eds911915
Thu Jul 12, 2012 3:05 am
Forum: Installation
Topic: EDIS-4 dwell
Replies: 1
Views: 3818

EDIS-4 dwell

is there a way to check dwell on a base edis-4 without MJ connected i know that the amount of teeth passing the vr sensor has alot to do with the amount of time the primary circuit stays open. im thinking to back probe pins 1&3 at the coil pack with an oscilliscope but not sure what type of wave...
by eds911915
Sun Jun 24, 2012 3:12 pm
Forum: Installation
Topic: finnally starting to get a clue
Replies: 2
Views: 4699

COP setup

I tryed to split the 2 trigger wires 10&12 at edis4 module or 1&3 at the coil take your pick. Anyway ended up with the same weak intermitant spark.
by eds911915
Sat Jun 23, 2012 3:27 am
Forum: Installation
Topic: finnally starting to get a clue
Replies: 2
Views: 4699

finnally starting to get a clue

looking for a good article/blog/how to, on edis-4 and coil on plug. i tryed wiring a single coil on plug (out of a 2010 mazda) jumped over from edis-4 connector pins 1&2 and VIOLA! i was getting a fat blue regular spark. oh man i got such a chubby when i saw that. but i still dont understand how...
by eds911915
Mon Jun 18, 2012 1:23 am
Forum: Installation
Topic: EDIS-4 Coil pack grounding
Replies: 2
Views: 4983

EDIS-4 Coil pack grounding

Can a bad coil pack ground cause a weak spark/ no spark condition? I have mine mounted to fender wall. when i was at the junkyard I noticed all the ford escourts have there coil packs mounted to the engine.
by eds911915
Thu Jun 07, 2012 1:46 am
Forum: General Discussion
Topic: Boost engineering
Replies: 6
Views: 9885

Boost engineering

Everytime i try to log into Boost Engineering i get message that says "Boost Engineering out of business" WTF happened?