Search found 12 matches

by Not Anumber
Tue Feb 11, 2014 7:52 pm
Forum: Installation
Topic: Aux input ?
Replies: 2
Views: 3010

It does have the pullup resistor. I will fit a secondary temperature sender.
by Not Anumber
Mon Feb 10, 2014 3:16 pm
Forum: Installation
Topic: EDIS spark loss
Replies: 11
Views: 8762

If in doubnt check the flux capacitor.
by Not Anumber
Mon Feb 10, 2014 2:50 pm
Forum: Hard Rev Limiter
Topic: Hard Cut Rev Limiter installed but not working.
Replies: 3
Views: 5614

Is it not powering the coil or is it not breaking the connection when the rev limit is reached ?
by Not Anumber
Tue Feb 04, 2014 9:51 am
Forum: Installation
Topic: retain original ignition as a fallback ?
Replies: 3
Views: 4257

That certainly convinced me. Done away with. Removing the old ignition system allowed a neater and simpler point to point wiring regime. As the installation is in a 7 type kit car that was built by someone else I was facing having to fathom the loom wiring with multiple lucar and bullet connectors a...
by Not Anumber
Mon Jan 27, 2014 11:12 pm
Forum: Installation
Topic: retain original ignition as a fallback ?
Replies: 3
Views: 4257

retain original ignition as a fallback ?

Having mounted the trigger wheel and sensor on my modified pinto I was about to start chopping out the wiring to the original electronic distributor based ignition when I paused. I could: Remove the electronic dizzy, leads, spark module, single coil and it's associated LT wiring, sell them on Ebay a...
by Not Anumber
Tue Jan 21, 2014 8:37 pm
Forum: Installation
Topic: Values for fuses recommendation
Replies: 8
Views: 7348

I am also planning on using 1 fuse for the coil and a seperate fuse for the Mjlj and Edis module.

I am presuming a 5 Amp fuse will be fine for the Edis(4) and Megajolt but does anyone know whether a 10 Amp will be enough for the coilpack please ?
by Not Anumber
Tue Jan 21, 2014 8:31 pm
Forum: Installation
Topic: Aux input ?
Replies: 2
Views: 3010

Aux input ?

The Mjlj v3 I am about to fit has an external Aux input circuit built on a daughter board in the case. This is wired to the Molex in place of the User Out 4 pin. There is a note this is a resistive input but I cannot tell if it is meant to measure resistance between this input and Ground or between ...
by Not Anumber
Mon Jan 20, 2014 3:37 pm
Forum: Operation
Topic: Melting the EDIS coil
Replies: 5
Views: 5775

It would be interestinbg to know what the cause was. it's unusual for coilpacks to go wrong, unheard of for 3x coilpacks to go bang one after another.
by Not Anumber
Thu May 09, 2013 9:50 am
Forum: Installation
Topic: seperate supply for coil ?
Replies: 3
Views: 3550

If you've got the hard rev limiter, the coil supply needs to go through the megajolt anyway. . Ive factored in running a relay from the MJ's hard rev limiter output to interupt the +v supply to the coil but thats just for switching. My question is really whether i should aim to use seperate +v cabl...
by Not Anumber
Tue May 07, 2013 3:30 pm
Forum: Installation
Topic: seperate supply for coil ?
Replies: 3
Views: 3550

seperate supply for coil ?

Is it desireable to use a seperate +v cables to the Megajolt and the Coilpack or can i use a existing supply cable (capable of delivereing 15 amps) to the Megajolt, Edis and the Coilpack ?
by Not Anumber
Sat Apr 20, 2013 7:04 pm
Forum: Installation
Topic: location choice for Edis ?
Replies: 3
Views: 3329

Many thanks Brent
by Not Anumber
Sat Apr 20, 2013 4:05 pm
Forum: Installation
Topic: location choice for Edis ?
Replies: 3
Views: 3329

location choice for Edis ?

I am new so I'll appologies if this has been asked many times before. I am finally getting round to installing the MJLJv3 on my kit car and am running the cables. Should I install the Edis4 module on the bulkhead in the engine compartment or would it be safer behind the dash in the passenger compart...