Search found 10 matches

by MikeStang
Tue Apr 02, 2019 3:27 pm
Forum: Lua Scripting
Topic: Mike Lua Questions
Replies: 9
Views: 2375

Thanks, good to know the X2 and X3 script will work together. I was initially confused because on power up the lights run back and fourth and change color. I now know this is where there is no CAN communication . I loaded the test Script that is on the website and it kind of works, not as I suspect ...
by MikeStang
Mon Apr 01, 2019 7:30 pm
Forum: Lua Scripting
Topic: Mike Lua Questions
Replies: 9
Views: 2375

Yup, I see the Write Tab and know to do that. I have saved files and send to my RC dealer for some assistance. I used Poll Log, but when the Baud Rate was wrong i was not able to see the issue in the Poll Log. Yes, there is a Clear and RUN tab. This is all new to me. I loaded the test Script that is...
by MikeStang
Sun Mar 31, 2019 2:23 am
Forum: Lua Scripting
Topic: Mike Lua Questions
Replies: 9
Views: 2375

CAN Bus Channel 2 Baud rate set to 500k from 250k, now X2 shift lights work.

So much info, such scattered placement...

Finally can start learning Scripting now that it is connected. Its odd that sometimes I write a script change and it does not take? I guess I will stumble through it.
by MikeStang
Sat Mar 30, 2019 7:54 pm
Forum: Lua Scripting
Topic: Mike Lua Questions
Replies: 9
Views: 2375

OK, Shift X2 now has power. It goes through a light sequence on power up, Red Green Blue run back and fourth, it does this with nothing in the "Scripting" section. If I copy and paste the "disco light" test as is says in the set up instruction, it does not do anything different. I changed it to CAN2...
by MikeStang
Fri Mar 29, 2019 1:31 am
Forum: Lua Scripting
Topic: Mike Lua Questions
Replies: 9
Views: 2375

I'm so new I don't even understand the previous comment. Regardless.... The X2 does not do anything... not even sure where to go from here. I can double check my wiring just to be sure (already checked several times before install) Update: So I missed that the RJ45 port does not actually supply a po...
by MikeStang
Thu Mar 28, 2019 4:24 pm
Forum: Lua Scripting
Topic: Mike Lua Questions
Replies: 9
Views: 2375

Mike Lua Questions

Figured I would start a thread about programming the Lua commands in my Race Capture Pro MK3. Bare with me I am learning... I have just started reading a book on Lua. Info: RC Pro MK3 with X2 Shift light. Not an OBD2 car so all my inputs are wired into Analog. ShiftX2 is wired to the RJ45 connector ...
by MikeStang
Wed Feb 20, 2019 4:38 pm
Forum: RaceCapture/Pro General Q&A
Topic: RPM Input
Replies: 6
Views: 2139

brentp wrote:If it is a clean 12v square wave, then you should be good to go without CoilX.
Yup, clean square wave. Took a pic of my scope with my phone, was gonna post, but screen glare makes it hard to see.
by MikeStang
Mon Feb 18, 2019 2:25 am
Forum: RaceCapture/Pro General Q&A
Topic: RPM Input
Replies: 6
Views: 2139

Yup, for sure 12v square waveform.
by MikeStang
Thu Feb 07, 2019 3:23 pm
Forum: RaceCapture/Pro General Q&A
Topic: RPM Input
Replies: 6
Views: 2139

Not 100% sure of the signal, it got stupid cold here so I have not got a chance to scope that signal. Was just curious if anyone knew. I will scope it and report back, thanks.
by MikeStang
Wed Feb 06, 2019 12:17 am
Forum: RaceCapture/Pro General Q&A
Topic: RPM Input
Replies: 6
Views: 2139

RPM Input

Can you use the MSD box output as the RPM input into the MK3 Pro? (Using FREQ1)

Noob question, I searched expecting to find the answer, but did not.