RegisterSearchFAQMemberlistUsergroupsLog in
Search found 39 matches
Author Message
PostForum: New Project Suggestions   Posted: Wed May 02, 2018 8:20 am   Subject: Tuning software

I'm very keen to try this. Will it work with MJLJ v3 or is it specific to v4?
PostForum: New Project Suggestions   Posted: Sat Dec 20, 2008 5:08 pm   Subject: Mac software

A linux version would be nice too...
PostForum: Q&A   Posted: Sun Nov 16, 2008 9:33 pm   Subject: Map sensor per port

Or just use a vacuum reservoir per sensor...
PostForum: Q&A   Posted: Sat Nov 15, 2008 4:56 pm   Subject: Map sensor per port

Then fit a servo to each idle air screw, write some software and you have self balancing carbs Wink
PostForum: Q&A   Posted: Thu Nov 13, 2008 7:39 am   Subject: Shield Cable - Can you use USB Cable?

I used a 4-core burglar alarm cable for pip/saw and to the TPS. It was about the thinnest wire I've ever had to strip but works fine. We're not running huge currents here.
PostForum: Q&A   Posted: Thu Nov 06, 2008 8:25 pm   Subject: Backfiring through Carburettor

Ah, ok, in that case it sounds like the things mentioned above (or the timing is very, very wrong).

EDIT: Just a thought, you say it's not as bad at revs. Could it be that your bracket resonates at ...
PostForum: Q&A   Posted: Thu Nov 06, 2008 8:49 am   Subject: Backfiring through Carburettor

Lots of carbs spit back, it's not uncommon when they're less than perfectly set up. I'd look at your carbs first because as you say it should spark at the right time or not at all.
PostForum: Operation   Posted: Mon Oct 20, 2008 6:21 pm   Subject: Wont start facing downhill

Water trapped somewhere?
PostForum: Hard Rev Limiter   Posted: Mon Oct 20, 2008 6:20 pm   Subject: 998 mini

I don't feel the soft limiter on mine. It screams straight up to the hard limit when it immediately starts popping and banging and feels like a sack of spanners has replaced my engine.
PostForum: Assembly   Posted: Sat Sep 06, 2008 9:06 am   Subject: Lead free solder

I'm always wary of using lead free solder in a high vibration environment. If you do use it, use it well. It might be wise to add some extra dampening/padding under the unit once in place. I've seen l ...
PostForum: Installation   Posted: Fri Jul 18, 2008 4:59 pm   Subject: using a timing light with megajolt

Set it to zero. It's not worth the hassle. Put marks on the trigger wheel and go off that.
PostForum: Future Upgrades   Posted: Fri Jun 06, 2008 6:48 pm   Subject: on board data logging

Has this been mentioned before? Is there enough free memory on the next generation board's processor to log data for later download?
PostForum: Future Upgrades   Posted: Tue May 27, 2008 7:46 am   Subject: Dual plug w/one megajolt

The megajolt already has memory for 2 maps. It sounds as if it should be simple to read alternately from each (if the map switching can happen fast enough) and send alternate SAW signals down one of t ...
PostForum: Ignition Map Library   Posted: Tue May 27, 2008 7:40 am   Subject: Pinto map

That's the one I used. Check it before you use it though - I had to change the rev limit and modify the load bins because they're set stupidly for no apparent reason.
PostForum: Q&A   Posted: Mon May 19, 2008 6:23 am   Subject: Use of a distributor


i think esv is suggesting using just one coil ie sending both trigger signals to one coil. sounds to me like it would work... interesting idea!
cheers

Yes. As I said, that might run into proble ...
 
Page 1 of 3 Goto page 1, 2, 3  Next
All times are GMT