RegisterSearchFAQMemberlistUsergroupsLog in
Search found 16 matches
Author Message
PostForum: New Project Suggestions   Posted: Fri Mar 18, 2011 4:35 pm   Subject: Electronic Controlled Automatic Choke Control

The Bosch "steppers" of that type I've seen are actually more like a servo, just without any built in control electronics: just a pot for position feedback. Wouldn't it just stop where it is ...
PostForum: New Project Suggestions   Posted: Thu Mar 17, 2011 5:17 pm   Subject: Electronic Controlled Automatic Choke Control

Hiya Ryan,

I've stumbled across this while having a nosey round the site. Any updates?

I've been doing similar (only really got as far as installing some hardware), I opted for a servo to operat ...
PostForum: Powered by Megajolt Gallery   Posted: Tue Jul 13, 2010 11:16 am   Subject: speed sensors

Sailesmarketing,com do some interesting adapters for speedos & there's 1 for The Acewell dashes too.

Interesting project, I hadn't thought of reading the data out of the MJ for Arduino based tr ...
PostForum: Assembly   Posted: Wed Sep 09, 2009 12:16 pm   Subject: What have I broken and fried!

New new9v battery tried still nothing. Sad
PostForum: Assembly   Posted: Tue Sep 01, 2009 8:28 pm   Subject: What have I broken and fried!

I know of the usb issue - mine worked, but wasn't up to flashing the processor so I have also tried a motherboard serial port 'n cable.

I don't think it's the battery, I've been using 4 AA's which ...
PostForum: Assembly   Posted: Sun Aug 30, 2009 10:08 am   Subject: What have I broken and fried!

As above, taken a backward step now won't acknowledge the reset with hc08sprg

Quicky recap:

Worked
PC crash with 18volts
Configurator timeout - can't read/write to MJ
hc08 reset worked (with ...
PostForum: Assembly   Posted: Sat Aug 29, 2009 6:59 pm   Subject: What have I broken and fried!

I could but I've already had it talking to a PC with 3.3. and it failed to do the same after the incident, but before I could upgrade the upgrade so I'd be surprised if it will make a difference. Does ...
PostForum: Assembly   Posted: Fri Aug 28, 2009 2:51 pm   Subject: still no dice

I dug out pc number 3 and managed to successfully run the firmware flash in dos to 3.3.1 but it still reports a timeout with 3.3.2 configurator. Confused
PostForum: Assembly   Posted: Thu Aug 27, 2009 6:48 pm   Subject: Thanks for the prompt reply Brent,

I wonder if the fault could have originated on the pc? It did it first via the usb port, so a few volts on offer there. I have also tried with a DB9 cable.

The regulator is marked LF50APB. It has p ...
PostForum: Assembly   Posted: Thu Aug 27, 2009 10:17 am   Subject: What have I broken and fried!

Couldn't decide which of the 2 existing and doubtless popular categories are most apt so thought a new one was best Shocked

V3 'jolt was working until my muppety actions hooking it to my PC on the ...
PostForum: Operation   Posted: Wed Jul 01, 2009 10:03 am   Subject: Error Message on Firmware Upgrade

Nothing connected to the aux pad on the board, it was on my desk with a 9v battery and no ground so probably just some stray voltage conducted through me. Maybe I'll get a visit off the static dischar ...
PostForum: Operation   Posted: Wed Jul 01, 2009 12:09 am   Subject: Error Message on Firmware Upgrade

I just noticed it recorded a change on aux input gauge in software when I held the case.
PostForum: Operation   Posted: Sun Jun 28, 2009 8:26 pm   Subject: Error Message on Firmware Upgrade

Successfully upgraded firmware to 3.3.0 with a proper cable Smile

I can report the same problem with running outputs off Aux - though my aux input has only been my finger so far.
PostForum: Operation   Posted: Sun Jun 28, 2009 1:06 am   Subject: Re: Error Message on Firmware Upgrade

I'm getting the same issue as Rich Sad

V3 board with ST232ABN serial controller chip
USB/ serial adapter ch340, reads 'n writes under V3.2 just fine

anything else I can try?
PostForum: Future Upgrades   Posted: Tue Jun 03, 2008 11:27 pm   Subject: MJLJ V4 in testing

Thanks for the prompt reply,

I had thought of doing similar with a cross over relay but it still uses your outputs up Sad

Attaching switching events to cells on the map would be rather good, ...
 
Page 1 of 2 Goto page 1, 2  Next
All times are GMT