RegisterSearchFAQMemberlistUsergroupsLog in
Search found 94 matches
Author Message
PostForum: AnalogX   Posted: Thu Sep 26, 2019 5:05 pm   Subject: Canbus using 2 AnalogX's

I believe the AX's are terminated by default, which is why I put one on both ends. the AFR's are not, so are you saying this schematic is correct? thanks for replying.
PostForum: AnalogX   Posted: Thu Sep 26, 2019 2:40 pm   Subject: Canbus using 2 AnalogX's

Seasons over so im looking to clean up/simplify my wiring. I am looking to switch every sensor over to a canbus style harness. 8 linear sensors and two canbus AFR controllers. by using two AX's (one e ...
PostForum: RaceCapture App Operation and General Q&A   Posted: Tue Feb 26, 2019 1:06 pm   Subject: Raspberry Pi support - enables a hard-wired, dedicated dash

of the two you listed I would choose the Waveshare. mostly because it has the lugs in the four corners which would make install easier. both appear to have lugs for mounting the Pi. I used an older Wa ...
PostForum: RaceCapture App Bug Reporting / Feature Requests   Posted: Fri Feb 15, 2019 2:03 pm   Subject: Rpi gpios to RCapp inputs

Brent, did I read somewhere in one of your posts your looking at being able to import the Rpi gpios into racecapture as sensor inputs? i'm looking at using HR-SC04 ultrasonic sensors to measure static ...
PostForum: RaceCapture App Bug Reporting / Feature Requests   Posted: Mon Feb 11, 2019 10:50 pm   Subject: Raspberry Pi 3+ Touch Screen

open the .kivy/config.ini file in your pi and replace the Input stuff so it looks likes this:

[input]
mouse = mouse
mtdev_%(name)s = probesysfs,provider=mtdev
hid_%(name)s = probesysfs,provider= ...
PostForum: RaceCapture/Pro General Q&A   Posted: Thu Feb 07, 2019 7:15 pm   Subject: RPM Input

Most all the MSD box's like a 6AL produce a 12volt square wave signal with a 20% duty cycle for a tach signal. simple answer is, yes.
PostForum: RaceCapture/Pro General Q&A   Posted: Tue Feb 05, 2019 11:25 pm   Subject: RPM slow response to app

its my gopro footage. at first i thought maybe it was a video issue. it just seems odd that i see the same rpm readings repeating. it will do the same thing sitting in the shop and reving the engine, ...
PostForum: RaceCapture App Operation and General Q&A   Posted: Tue Dec 18, 2018 6:33 pm   Subject: Raspberry Pi support - enables a hard-wired, dedicated dash

here's a link to a step by step a did for another racer. it may help. also has some tricks for faster boot speed.

https://drive.google.com/open?id=1CwOL8fCX7YcXRKXOqnaiLb6lIojfyrsbM8fBBMHqcpA
PostForum: RaceCapture App Operation and General Q&A   Posted: Tue Dec 18, 2018 6:23 pm   Subject: Raspberry Pi support - enables a hard-wired, dedicated dash

Ok, so for future reference the logs are located in /home/pi/.kivy/logs. (I think, going by memory lol). you'll see a bunch of kivy_xx_x-x.txt because it logs a new one each time you open RCapp. perso ...
PostForum: RaceCapture App Operation and General Q&A   Posted: Tue Dec 18, 2018 3:20 pm   Subject: Raspberry Pi support - enables a hard-wired, dedicated dash

i'll try to help, but not an expert. I don't have the 7" official screen, but have run into a similar problem. try this first.

if you can get to a pi command line (with internet access connect ...
PostForum: Lua Scripting   Posted: Mon Dec 10, 2018 11:49 pm   Subject: Help with setting u calculated channel for F/R brake balance

This will read the % of front vs rear.

avgId = addChannel("FwdBrkBias", 10, 0, 0, 100, "%")
function doBias()
local a1 = getAnalog(0)
local a2 = getAnalog(6)
setChann ...
PostForum: Lua Scripting   Posted: Thu Dec 06, 2018 1:07 pm   Subject: Calculated channel - brake bias

I'm not a lua expert but i'll try to help. If your pulling two analog channels then try this from the Lua Scripting examples. you'll end up with a virtual guage that will show front bias as a percent ...
PostForum: RaceCapture/Pro General Q&A   Posted: Mon Dec 03, 2018 7:58 pm   Subject: RPM slow response to app

Watching some in car footage i noticed the RPM guage seems to show the same readings alot. like "5445". its not smooth or updateing fast enuff? any thoughts on what would cause this.

Here ...
PostForum: CAN mapping discussion   Posted: Thu Nov 29, 2018 8:24 pm   Subject: Ecotron CANbus AFR controller preset?

Im looking at possibly replacing my pair of Spartan AFR digital controllers with the Ecotron CANbus AFR controllers. would it be possible to have them added as a AnalogX preset? Here is a link to thei ...
PostForum: Lua Scripting   Posted: Mon Nov 26, 2018 12:42 pm   Subject: MaxRPM reset button

absolutely! Thanks.
 
Page 1 of 7 Goto page 1, 2, 3, 4, 5, 6, 7  Next
All times are GMT