RegisterSearchFAQMemberlistUsergroupsLog in
Search found 19 matches
Author Message
PostForum: Hardware and Installation   Posted: Thu Oct 24, 2019 6:23 am   Subject: Podium Hardware CAN Warning lamp turn on

Hello brentp-san,

Thank you for your strongly support.

i will change baud late to 1MB.(maybe current 500)
PostForum: Hardware and Installation   Posted: Sat Oct 12, 2019 2:22 pm   Subject: Podium Hardware CAN Warning lamp turn on

Hello ,

gentlly reminder.

Even though i introduced podium to shop.
But this one did not correctly work.

We use podium with AIM solo DL.

If use this one , GPS had 3min delay. Then CAN si ...
PostForum: Hardware and Installation   Posted: Sun Sep 29, 2019 10:53 am   Subject: Podium Hardware CAN Warning lamp turn on

Hello ,

i set up Podium what my friend get.
Then i try to use it.
Unfortunatery it could not correctly work.

i saw everytime CAN red lamp turn on.

So, i try to install latest farmware .
i ...
PostForum: CAN mapping discussion   Posted: Thu Jun 06, 2019 8:28 am   Subject: Directry CAN mapping for Podium

In this case , could not see signal.

But i think mapping will simuler before case.
PostForum: CAN mapping discussion   Posted: Thu Jun 06, 2019 8:25 am   Subject: Directry CAN mapping for Podium

Hello Ferg-san,

Thank you for quickly reply.

Actually , i try to other vehicle.
i attached 2 mapping. One was done, other is not....

i think this case can ignor little endian and big endian. ...
PostForum: CAN mapping discussion   Posted: Tue Jun 04, 2019 1:43 am   Subject: Directry CAN mapping for Podium

Hello,

i try to input some value.
i had negative result.
Probably i understood RC mapping rule for bit mode.

One thing , regarding your advice about below.

>Case A: Offset 2, Length 1 ...
PostForum: CAN mapping discussion   Posted: Wed May 22, 2019 8:21 am   Subject: Directry CAN mapping for Podium

Hello ,

Of course i tried to along this document.
But i did not get positive result.

Could you tell me more detail.

If check the Bit Mode , how to input Offset and Length in A and B case.
...
PostForum: CAN mapping discussion   Posted: Thu May 16, 2019 5:31 am   Subject: CAN mapping except 1 or 2 byte

Hello Brentp-san,

i could directly see CAN mapping data for 1 or 2 length(1(8bit) or 2(16bit) byte).

i want to see except 1 or 2 length.
For example 1 bit type and 12 bit type.

You can see a ...
PostForum: CAN mapping discussion   Posted: Tue Apr 30, 2019 4:59 am   Subject: Directry CAN mapping for Podium

Hello brentp ,

Thank you for your advice.

In this case , Do i need add some source to Lua?

If yes , could you tell me how to add source ?
PostForum: RaceCapture/Pro General Q&A   Posted: Sun Apr 21, 2019 1:38 pm   Subject: How to use Podium for VBOX?

Hello,

i usually use podium for AIM solo/solo2.
i try to use VBOX.
Thou, i got connector & pin.
Could you tell me how to use Podium for VBOX?
PostForum: CAN mapping discussion   Posted: Tue Apr 16, 2019 1:02 pm   Subject: Directry CAN mapping for Podium

i am using Podium with AIM SOLO & SOLO2.
Unfortunatery , i can see only limited CAN signal along SmartyCom Stream.
i want to see other signal that CAN mapping.
If possible , could you tell me ...
PostForum: Feature Requests   Posted: Tue Apr 16, 2019 12:37 pm   Subject: Telemetry For 5G system

Next year some country will bigin 5G network.
Thou , we can use this network.
Please update some system for this changing.
Especially , i want to request what extend podium system.
PostForum: RaceCapture App Bug Reporting / Feature Requests   Posted: Thu Jan 10, 2019 11:13 am   Subject: Analysis could not see on RaceCapture APP for Win7

Hi,

i had simular situation.

U can see above title.
PostForum: AnalogX   Posted: Sat Jan 05, 2019 8:34 am   Subject: Prepare other CAN ID?

Hello Ferg-san,

Thank you for your reply.

Need to cut the bridge each ADR?
How do i cut them?
PostForum: RaceCapture App Bug Reporting / Feature Requests   Posted: Fri Jan 04, 2019 2:12 pm   Subject: Analysis could not see on RaceCapture APP for Win7

Hello,

i installed RaceCapture APP 1.13.1 to Win7.
if i click the "Analysis", stopped working and program done.
Could you solve this issue ,please?
 
Page 1 of 2 Goto page 1, 2  Next
All times are GMT