RegisterSearchFAQMemberlistUsergroupsLog in
Search found 6294 matches
Author Message
PostForum: RaceCapture App Operation and General Q&A   Posted: Wed Mar 25, 2020 12:32 am   Subject: Raspberry Pi support - enables a hard-wired, dedicated dash

With the Raspberry Pi 4, they completely changed the graphics driver. We will be rolling out support with the 2.0 version of the RaceCapture app, due out within a couple of months.

We'll post in t ...
PostForum: RaceCapture/Pro General Q&A   Posted: Mon Mar 23, 2020 2:57 am   Subject: RaceCapture/Pro MK3 in a 1999 Miata


What temperature and pressure sensors are you using? Do you have the calibration information? This would be a chart showing the resistance value of the sensor across a temperature or pressure ...
PostForum: News and Announcements   Posted: Mon Mar 16, 2020 12:14 am   Subject: TireX - CAN enabled multi-zone tire temperature sensor

Announcing TireX - a ruggedized, CAN bus enabled multi-zone tire temperature sensor. Sign up to get notified when pre-orders launch:
PostForum: Sensors   Posted: Mon Mar 16, 2020 12:11 am   Subject: DIY cheap wireless 16 zone tire temp sensor

Good news - we are readying pre-orders for TireX - a ruggedized CAN bus enabled multi-zone tire temperature sensor that will work with RaceCapture: ...
PostForum: Telemetry   Posted: Tue Mar 10, 2020 4:17 pm   Subject: New Podium app is available for beta testing

Hi Ray,

1) You can't, yet. this is a feature we will enable in the future.

2) Not yet, this will also be added in in a future release.

Thank you,
PostForum: AnalogX   Posted: Mon Mar 09, 2020 2:33 pm   Subject: Connecting to Miata Fuel Sensor

Don't use too small of a resistor, otherwise the current consumption will be high. Use an ohms law calculator to ensure you don't exceed more than 100mA or so.
PostForum: Telemetry   Posted: Mon Mar 02, 2020 3:48 pm   Subject: Problem staying connected to Podium

Glad you got it figured out. Thanks for the update!
PostForum: CAN mapping discussion   Posted: Sun Feb 23, 2020 6:10 pm   Subject: Bug in Bit Mode Channel Mapping? Doesn't work above 20?

Tracking here:

What we will do to reproduce is to connect CAN1 and CAN2 in loopback, and then send data from CAN1 to CAN2 u ...
PostForum: RaceCapture/Track Operation   Posted: Sat Feb 22, 2020 6:07 pm   Subject: Manual logging start with RC Track?

Agreed, it's on the to-do list, hopefully in V2 of the RaceCapture app.
PostForum: RaceCapture App Operation and General Q&A   Posted: Thu Feb 13, 2020 11:52 pm   Subject: organize Racecapture displays

Should be out Q1 of this year.
PostForum: RaceCapture/Track Installation   Posted: Thu Feb 13, 2020 10:04 pm   Subject: Bluetooth / USB to Eonon Android Headunit in E46 Issues

I remember the Eonon unit's bluetooth isn't compatible with the same bluetooth, but USB OTG *should* work.

You could try USB OTG on a different device, such as a Fire 8 tablet, as a comparison.
PostForum: Lua Scripting   Posted: Thu Feb 13, 2020 10:01 pm   Subject: Calculated fuel consumption?


There isn't a way to measure duty cycle, but we do have a different suggested way of doing it, via direct measurement of fuel flow: ...
PostForum: Telemetry   Posted: Thu Feb 13, 2020 9:58 pm   Subject: Problem staying connected to Podium


You will need to ensure only one device is set for streaming to Podium. If there are two devices, then podium will continuously disconnect the old connection when the new connection attaches. ...
PostForum: Hardware and Installation   Posted: Thu Feb 13, 2020 9:56 pm   Subject: RCP MK1 Terminal Block P/N

We don't have a specific part number, but it is a standard right angle pluggable terminal block with 3.5mm pitch: ...
PostForum: RaceCapture/Pro General Q&A   Posted: Thu Feb 13, 2020 9:53 pm   Subject: Possible to log CAN data on RCP MKI?


The MK1 firmware doesn't have direct CAN mapping in the firmware, but you should be able to use the Lua scripting to send and receive CAN messages. ...
Page 1 of 420 Goto page 1, 2, 3 ... 418, 419, 420  Next
All times are GMT