RegisterSearchFAQMemberlistUsergroupsLog in
Search found 16 matches
Author Message
PostForum: Hard Rev Limiter   Posted: Mon Nov 13, 2017 8:44 am   Subject: Are empty holes OK ?

Hi, thanks for your help.
Cornelius
PostForum: Hard Rev Limiter   Posted: Fri Nov 10, 2017 3:50 pm   Subject: Are empty holes OK ?

here is the picture
PostForum: Hard Rev Limiter   Posted: Wed Nov 08, 2017 10:56 am   Subject: Are empty holes OK ?

Hi,
many, many years ago,
I bought a Hard Rev Limiter V 1.2.0.
I am about to put it in my only recently purchased MegaJolt.

I have read the instructions and
I understand that I have to solder ...
PostForum: Operation   Posted: Tue Sep 30, 2014 9:07 pm   Subject: Aftermarket knock sensors

@ Oliver

I had a look at the site you mentioned.
There are 4 different products.
Which one have you bought and used ?
PostForum: Operation   Posted: Wed Sep 10, 2014 8:07 pm   Subject: Aftermarket knock sensors

This is not from me, but
I saw some photos here:
www.lathyrus.eu

than click on:
Special tools and parts

than click on:
Knock detection circuit
PostForum: Installation   Posted: Sun Jun 22, 2014 10:37 am   Subject: Spark plug wiring for a Rover V8

Hi,

here is a picture with my installation.
Rover V 8 3.5 in a Triumph TR 7.
I swapped the HT cables until it locked tidy.
As said before, you can swap cables on EACH coil,
not between the coi ...
PostForum: Operation   Posted: Tue Apr 22, 2014 8:16 am   Subject: Question about Flash

Thanks, Brent

Cornelius
PostForum: Operation   Posted: Sun Feb 16, 2014 2:12 pm   Subject: Question about Flash

Hi,
I have a MegaJolt V3 and I'm about to put it in my car.
EDIS is running already in Limp Home mode.
I have some questions about flashing.
I have found this and I quote from the Operation guide: ...
PostForum: Installation   Posted: Fri Nov 22, 2013 3:15 pm   Subject: Values for fuses recommendation

«
I don't like to use any more terminals and connectors than absolutely necessary«

I totally agree with your statement.
I just could leave two slots for the fuses empty.

Are the wires all on o ...
PostForum: Installation   Posted: Wed Nov 20, 2013 3:10 pm   Subject: Values for fuses recommendation

One reason is, I have this nice little holder for the relay.

The other reason is, I can distribute easily the power from one point
to the four devices. Two coil packs, EDIS module, and MegaJoltBo ...
PostForum: Installation   Posted: Tue Nov 19, 2013 4:13 pm   Subject: Values for fuses recommendation

I'm about to put the MegaJolt EDIS into my car.
I have planned to put some fuses and a relay in.
What values of fuses should I use ?
Please have look at my sketch.
PostForum: Q&A   Posted: Thu Jan 27, 2011 9:49 am   Subject: What software do I need for megajolt V 3 ???

I don't use any USB-Serial Adapter, so no problems there.
Than I wired a switch in the power supply.
That made all the difference.
It worked!
Thanks again Brent.

Cornelius
PostForum: Q&A   Posted: Wed Jan 26, 2011 12:20 pm   Subject: What software do I need for megajolt V 3 ???

Hi Brent,

thanks for your answer.

Sorry I can't report a success.

I followed the steps in the firmware upgrade guide.
I got the "Waiting for...." message and than: "received 0 ...
PostForum: Q&A   Posted: Tue Jan 25, 2011 4:43 pm   Subject: What software do I need for megajolt V 3 ???

Hi,

I have read this forum a couple of hours.
Found an answer somewhere else, saying: you should download V 3.2.1
I did it and connected the MJLJ board.
I got a message that this version does no ...
PostForum: Q&A   Posted: Sun Jan 23, 2011 12:20 pm   Subject: What software do I need for megajolt V 3 ???

Hi Ryan,

thanks for your answer.
I found the following versions:
V3.0.0
V3.1.0
V3.1.1
V3.1.2
V3.2.0
V3.2.1
V3.3.0
V3.3.1
V3.3.2

Which version should I download onto my computer ?

Co ...
 
Page 1 of 2 Goto page 1, 2  Next
All times are GMT