RegisterSearchFAQMemberlistUsergroupsLog in
Search found 213 matches
Author Message
PostForum: Assembly   Posted: Mon Jul 11, 2016 12:45 pm   Subject: Going back to MAP

I flashed the latest firmware, and the MAP response is now working again. Very Happy

All I have to do now is to get the carb tuned properly...

Many thanks for the help,
David
PostForum: Assembly   Posted: Sat Jul 09, 2016 6:03 pm   Subject: Going back to MAP

Many thanks!

I'm currently trying to refresh my memory regarding the way MJLT is configured... Shocked
It's been working so well I've forgotten how to set it up!

I've changed from TPS to MAP in ...
PostForum: Assembly   Posted: Sun Jun 26, 2016 6:30 pm   Subject: Going back to MAP

Hi!

First of all - I can say with some pride that I've now been running my Megajolt for almost 10 years on [url=https://forum.autosportlabs.com/viewtopic.php?t=1092]this car! It's been so reliable ...
PostForum: RaceCapture/Pro introductions   Posted: Mon Mar 17, 2014 4:35 pm   Subject: Been away a long time!

This not so much an introduction, more of a 'hello again!'. I haven't been on this forum for at least 6 years, probably more, so I'm really starting from scratch once again.

Absolutely ages ago I i ...
PostForum: Q&A   Posted: Fri Nov 27, 2009 10:03 pm   Subject: Why earth mjlj and edis at the same point?

Also...

If you have a loop of wire it can pick up electromagnetic signals. If you have separate earths then stray signals can be picked up in the loop between chassis point A - MJ - EDIS - chassis ...
PostForum: New Project Suggestions   Posted: Sun Oct 18, 2009 12:33 pm   Subject: Knock Control

Now then i read on a certain speed of auto website that he made a knock sensor for tuning, but instead of your typical ecu controlled sensor, he used a small microphone epoxied to a battery terminal t ...
PostForum: News and Announcements   Posted: Fri Aug 21, 2009 11:59 am   Subject: The mark of speed- and falling to peer pressure

I like it, very funny! Also could be construed as Picasso, brent, as well as leadfoot.

Doh!

I didn't register what it meant until I read that! Shows how well I did in school chemistry, doesn't ...
PostForum: Installation   Posted: Thu Jul 23, 2009 7:27 pm   Subject: Where can I buy loom tape?

Do you REALLY want to use that stuff? It's fine if you never want to make changes to the wiring, otherwise it's a total PITA.

I would recommend split convoluted tubing - very neat, if done properl ...
PostForum: Installation   Posted: Wed Jul 15, 2009 11:34 am   Subject: Screened cable ?

http://trigger-wheels.com/store/index1.html is your friend...

...or you can go to Maplins and get general-purpose twin-screened cable a bit cheaper. Personally I preferred to use cable that was in ...
PostForum: Installation   Posted: Tue Jun 16, 2009 11:24 am   Subject: Ford VR Crankshaft Sensor polarity

Try this link

http://www.locostbuilders.co.uk/viewthread.php?tid=112060

(halfway down the page)
PostForum: Installation   Posted: Wed May 27, 2009 1:49 pm   Subject: TPS Help - R1 Carbs

A multi-meter is your friend here! A cheapie can be bought in Maplins for just a few Pounds, if you don't have one already (or, if not in the UK, your favourite electrical shop).

Set the meter to ...
PostForum: Operation   Posted: Tue May 19, 2009 3:52 pm   Subject: Runs great but real pain to start

You say that it's not a good starter if it's been left for a while - how healthy is the battery? They do lose charge over time, especially if they're not so new.

Mine has a maintenance charger per ...
PostForum: Operation   Posted: Sun May 17, 2009 9:39 pm   Subject: Runs great but real pain to start

I have a 1660 xflow with bike carbs + tps, and Megajolt. Mine starts first go almost every time, Summer or Winter! (but I'm sure you don't want to know that! Very Happy )

I leave my plugs as they come out ...
PostForum: Installation   Posted: Sat May 16, 2009 9:40 am   Subject: Suitable TPS

The advantage of the triggerwheels one is that it can be mounted either way around, to suit the throttle spindle rotation - the one I had was one-sided, but fortunately it was the right side! Very Happy
PostForum: Installation   Posted: Fri May 15, 2009 11:31 am   Subject: Suitable TPS

I wanted one to fit onto a Weber 32/36 DGV carb - went to a decent scrappy and got one from a Ford Escort/Orion (I think).

Generally they are very similar - a screw slot each side of the round body ...
 
Page 1 of 15 Goto page 1, 2, 3 ... 13, 14, 15  Next
All times are GMT