RegisterSearchFAQMemberlistUsergroupsLog in
Search found 25 matches
Author Message
PostForum: Operation   Posted: Wed Apr 08, 2009 4:27 pm   Subject: Megajolt Tps won't map

I have a similar problem -only worse. I've calibrated my TPS and the load meter moves in response to the throttle pedal but I get no movement at all in the load axis of the map -the dial goes around ...
PostForum: Future Upgrades   Posted: Tue May 29, 2007 3:11 pm   Subject: diagnostics ?

What about some simple diagnostics, either from a plugged in PC or using the switched ouputs - to show for example crank sensor is triggering, MJ is running (flashing an output as a watchdog? ), Progr ...
PostForum: Future Upgrades   Posted: Tue May 29, 2007 3:03 pm   Subject: starting point

I'd go with this a being a great idea too - its almost impossible ( with my skills anyway) to get the trigger wheel & sensor aligned spot on ( seems confusing to adjust too when you've looked at t ...
PostForum: Bug Reporting   Posted: Tue May 29, 2007 2:37 pm   Subject: shift light glow

Not quite the same as mine -mine is there all the time from startup . It is on one output LED only ( notably the red one -which I'm guessing is the most sensitive in terms of light output/mA, other d ...
PostForum: Bug Reporting   Posted: Tue May 01, 2007 10:08 am   Subject: shift light glowing

I have a glowing shift light too - it flickers dimly. It is only on one output (I use four outputs to drive LEDS). Because it flickers I've put it down to some sort of noise problem - I don't *thin ...
PostForum: Operation   Posted: Fri Apr 27, 2007 2:16 pm   Subject: Utility for identifying com port

Hi,

Deos anyone have simple utility for identifying what com port is bieng used for the Rs232 lead with a quick click ? Its bit of a bind to do the control panel/system/hardware/deive manager etc ...
PostForum: Operation   Posted: Tue Apr 10, 2007 8:39 pm   Subject: A problem....Help :-)

Hi,

Dunno but ....

** Have you checked the gap between the crank sensor and the an the toothed wheel ??

** It could also be a noise problem -the latest MJ software has adjustable filtering ...
PostForum: Fixes/Patches/Updates   Posted: Mon Apr 09, 2007 3:56 pm   Subject: Version 3.2.1 firmware and configuration software

I've updated my firmware with this verison and used the new MJ -all works fine, not seen any problems -FTDI chipset USB/RS232 lead.



Smile
PostForum: Powered by Megajolt Gallery   Posted: Tue Apr 03, 2007 7:26 pm   Subject: Westfield with 2ltr CVH and Megajolt............

Nice job Jenko - I've posted mine on this forum too .


Nice ot see soemthing a bit different - a 2.0 CVH !!

CU on WSCC....

Paul.
PostForum: Powered by Megajolt Gallery   Posted: Tue Apr 03, 2007 7:15 pm   Subject: 1700 X/flow Westfield install

Hi all,

just completed my MJ install and ran my 1700 Westfield.

The car is a typical 135 BHP spec Westfield with bored out 1600 Cross flow motor , ported head, A2 cam . The car runs much bette ...
PostForum: News and Announcements   Posted: Fri Mar 23, 2007 12:23 pm   Subject: Perhaps the ultimate DIY shift light!

Hi,

I've made my shift light from an LED torch off Ebay - very cheap.

I took two leds out and replaced them with a single red and green LED. I then cut the back of the ciruit board about to brin ...
PostForum: Bug Reporting   Posted: Sat Mar 10, 2007 5:17 pm   Subject: V3.0.0 / V3.1.0 Configurator USB-Serial problems

Hi,

just tried version 3.1.1 - It works fine with my FTDI Serial to USB convertor lead (version 3.1.0 would not write data to the MJ with this lead) . The "Hugepine" device works but cr ...
PostForum: Bug Reporting   Posted: Thu Mar 08, 2007 9:15 am   Subject: V3.0.0 / V3.1.0 Configurator USB-Serial problems

I will give it go at the weekend, thank you and fingers crosssed


Very Happy
PostForum: Fixes/Patches/Updates   Posted: Fri Mar 02, 2007 3:01 pm   Subject: Firmware 3.1 installed and working

Hi you can import megajolt maps into Excel and print/graph them from there.
PostForum: Q&A   Posted: Fri Mar 02, 2007 2:12 pm   Subject: Sticker

Hi,

Any more progress on the sticker front ?? - these have to be good advertising for the product and worth 10bhp in their own right.

I'd certainly like to purchase a couple


Failing that an ...
 
Page 1 of 2 Goto page 1, 2  Next
All times are GMT