RegisterSearchFAQMemberlistUsergroupsLog in
Search found 13 matches
Author Message
PostForum: Ignition Map Library   Posted: Sun Apr 17, 2011 4:49 pm   Subject: Duratec MJ maps ?

Just started the process of an engine change from the 2litre Pinto to a 2 litre Duratec.

Are there any maps about for a Duratec with twin carbs (dellorto 40's) ?
PostForum: Operation   Posted: Thu Aug 12, 2010 9:25 pm   Subject: Oh no, not another "I cant connect" thread

Right- ok. So Pin 3 and 4 are connected to ground on the PC board. In the DB9-RJ11 adapter we provide we only connect DB9 pin 5 to one of the RJ11 pins- that is sufficient.

Did you build your own ...
PostForum: Operation   Posted: Thu Aug 12, 2010 8:46 pm   Subject: Oh no, not another "I cant connect" thread

Have now tried 3 different laptops - 1 with a proper serial connector and the other 2 with 2 seperated USB/Serial Adapters, but still cannot communicate with the MJLJ. The only thing that I can see i ...
PostForum: Operation   Posted: Thu Aug 12, 2010 8:20 pm   Subject: Oh no, not another "I cant connect" thread

Have now tried 3 different laptops - 1 with a proper serial connector and the other 2 with 2 seperated USB/Serial Adapters, but still cannot communicate with the MJLJ. The only thing that I can see i ...
PostForum: Operation   Posted: Thu Aug 12, 2010 7:34 pm   Subject: Oh no, not another "I cant connect" thread

Have now tried 3 different laptops - 1 with a proper serial connector and the other 2 with 2 seperated USB/Serial Adapters, but still cannot communicate with the MJLJ. The only thing that I can see i ...
PostForum: Operation   Posted: Wed Aug 11, 2010 9:36 pm   Subject: Oh no, not another "I cant connect" thread

How new is your Megajolt unit? if reasonably recent then you will likely have the 4.0.2 firmware, which matches up with the 4.0.2 software. Normally you will not need to re-flash the Megajolt as we pr ...
PostForum: Operation   Posted: Wed Aug 11, 2010 4:13 pm   Subject: Oh no, not another "I cant connect" thread

Another thought - I will be initially running the Car without a TPS (or MAP) sensor. so have found a 2D map. I notice in the config screen it aks to specify TPS or MAP usage, but does not allow a &q ...
PostForum: Operation   Posted: Wed Aug 11, 2010 4:07 pm   Subject: Oh no, not another "I cant connect" thread

EDIT :

So I thought I would try an dload the latest firmware. This is the response I got, which I guess implies that at least there was some type of communication going on ?


C:\Documents and ...
PostForum: Operation   Posted: Wed Aug 11, 2010 3:51 pm   Subject: Oh no, not another "I cant connect" thread

Yep, Sorry.

I cant get my laptop to connect with the MJlite jnr.

It is installed in the car and the Green light comes on when the ignition is switched on. I have tried connecting using my lapto ...
PostForum: Installation   Posted: Mon Aug 09, 2010 3:14 pm   Subject: My MK Indy (pinto) swap from Dizzy to EDIS and MJ

Sounds like your wire is only hot when the key is on. You need a lead that is hot in START and RUN. Good luck.

Yep, thanks. I id go for a ignition live back at the key barrel, but it appears that ...
PostForum: Installation   Posted: Mon Aug 09, 2010 12:04 pm   Subject: My MK Indy (pinto) swap from Dizzy to EDIS and MJ

So now I am a bit confused.

I have found an ignition live directly off the Igntion barrel (yellow wire). However, if I connect the edis directly to the battery and a ground, then the car will run, ...
PostForum: Installation   Posted: Sun Aug 08, 2010 6:41 am   Subject: My MK Indy (pinto) swap from Dizzy to EDIS and MJ

I have removed the coil/dizzy setup from the Pinto engine now and have had it running with the Coil Pack and edis4, but without the MJ yet. All I did was to wire direct to the battery (with a fuse) t ...
PostForum: Q&A   Posted: Sat Jun 05, 2010 5:43 pm   Subject: Rolling road tuning

Bit further to travel, but I know that Northampton Motorsport will rolling road a MegaJolt
 
Page 1 of 1
All times are GMT