RegisterSearchFAQMemberlistUsergroupsLog in
Search found 14 matches
Author Message
PostForum: Operation   Posted: Mon Jun 13, 2011 9:37 am   Subject: Cranking advanced

right got yeah, nice one but i thought that you could fine tune the timing up to a few degrees, im not sure if its right as the motor still runs for a few seconds after i switch it off?
PostForum: Powered by Megajolt Gallery   Posted: Sun Jun 12, 2011 7:19 pm   Subject: My 1380 mini


Long time since the last post but i had my engine rolling roaded for the first time around a month ago just to get the basic settings so i could run the engine in, it managed to get 111bhp at 57 ...
PostForum: Operation   Posted: Sun Jun 12, 2011 7:01 pm   Subject: Cranking advanced


How do i check cracking advanced on the megajolt software, and how do i adjust it and what too?, i know thats a lot to ask but the engine it not running smooth at all

any help would be apprec ...
PostForum: Q&A   Posted: Sun May 29, 2011 1:03 pm   Subject: map pipe


sorry for the late reply, but its in the top of the manifold im running twin HS4's so it in the middle of the balance pipe on the manifold, its none turbo

PostForum: Q&A   Posted: Tue Apr 26, 2011 8:36 pm   Subject: map pipe


had my engine running now for a while and I've noticed that the map pipe fills with fuel vapor (fuel) over time how can i stop this? iv had my car rolling roaded so it's not over fueling, im won ...
PostForum: Q&A   Posted: Wed Apr 13, 2011 6:16 pm   Subject: map pipe

I'm running my engine in for the frist time and iv noticed a problem my map pipe to my jolt squashes when I'm reving it, can anyone recomended the pipe I should use?

PostForum: Operation   Posted: Tue Apr 05, 2011 8:54 pm   Subject: Need help adjusting map for rolling road

Thats just what i was looking for nice one

PostForum: Operation   Posted: Mon Apr 04, 2011 9:27 am   Subject: Need help adjusting map for rolling road

Hi all

I need help adjusting my map due to the rolling road guy, he will tell me what to put in but he's not willing to do it himself Sad iv put a base map which is a close spec to my engine but i h ...
PostForum: Powered by Megajolt Gallery   Posted: Thu Jul 01, 2010 9:25 am   Subject: My 1380 mini

Thanks guys il try and have some videos up soon of it running, at tho mo it runs but its a bit dodgy, il aslo get some pics up where iv mounted the megajolt module too.

PostForum: Powered by Megajolt Gallery   Posted: Tue Jun 29, 2010 11:40 am   Subject: My 1380 mini

My 1380 spec
A+ block board to 73.5mm
•Megajolt ignition system
•Twin HS4's
•ported and polished cylinder head 36mm inlet 31mm exhaust
center main strap
•Billet 286 kent cam and followers
•ligh ...
PostForum: Ignition Map Library   Posted: Tue Jun 29, 2010 11:26 am   Subject: 1380 mini

Hi Ryan

Thanks for looking for me il try the spi2 map to see if that will work for me, at the mo im running the aldon yellow map but not sure if its doing it any good as im running my engine in sti ...
PostForum: Ignition Map Library   Posted: Mon Jun 28, 2010 10:53 am   Subject: 1380 mini

Need map for this engine asap please if anyone can help?
PostForum: Installation   Posted: Tue Jun 15, 2010 8:59 am   Subject: Massive problem! Coilpack / EDIS?

Hi there

i have the same rev counter as you how did you wire it up to work as mine just sits there!
PostForum: Ignition Map Library   Posted: Wed Apr 14, 2010 3:44 pm   Subject: 1380 mini


Im Richard and iv just built myself a 1380 spec below

•Twin HS4's
•Slark SF4 cylinder head
•1380 block with centre main strap
•Billet 286 kent cam and followers
•lightened steel flywhee ...
Page 1 of 1
All times are GMT