RegisterSearchFAQMemberlistUsergroupsLog in
Search found 28 matches
Author Message
PostForum: Hardware and Installation   Posted: Fri Oct 16, 2015 8:43 am   Subject: Can-X Module Wiring

I have a Can-X module for a Mk1 RCP, and was looking at connecting it to my test rig CAN bus.

I looked on the website and can see that the pins on the actual RCP socket run from 1 to 8 (left to rig ...
PostForum: Hardware and Installation   Posted: Thu Feb 05, 2015 3:35 pm   Subject: Expansion Port PinOuts

We'll see what we can do with a flat rate envelope and adjust the cost.

Thanks!

Ok, cheers.

I have ordered it already Smile (request 239)
PostForum: Hardware and Installation   Posted: Thu Feb 05, 2015 8:30 am   Subject: Expansion Port PinOuts

Here you go. We currently have 3 modules in stock, lovingly hand built and tested.

http://www.autosportlabs.com/product/canx-can-bus-expansion-module/

Hi Brent,

I just went to order one, but ...
PostForum: Hardware and Installation   Posted: Tue Feb 03, 2015 11:05 am   Subject: Expansion Port PinOuts

So there's nothing special about the CANx module that makes it OBD2 specific. for a generic CAN interface you would just connect GND and CAN+ and CAN-. We'll have documentation and pinouts when it's r ...
PostForum: Hardware and Installation   Posted: Tue Jan 20, 2015 10:11 pm   Subject: Function Generator

Can anyone tell me the spec of a signal/function generator that is capable of generating all the signal types I might expect to capture on the RCP?

I want to simulate sensors in the warmth of my lo ...
PostForum: RaceCapture/Pro General Q&A   Posted: Tue Jan 13, 2015 3:53 pm   Subject: RCP MK1 - expansion port active?

Hi Brent,

Hi - Which link above is broken / does not work?

The github one, but I guess it could be my work proxy....


We are gauging interest in the CANx module to determine how big of a pro ...
PostForum: RaceCapture/Pro General Q&A   Posted: Tue Jan 13, 2015 9:38 am   Subject: RCP MK1 - expansion port active?

So I have a Mk1, and have been waiting for the CANx module since I bought it (it was the ONLY reason I bought an RCP). The link above doesn't work. What's happening with this?

My car doesn't have a ...
PostForum: RaceCapture/Pro General Q&A   Posted: Wed Nov 12, 2014 10:39 pm   Subject: OBDII via bluetooth?

Think I might be being dumb. Just looked on my ECU doc and it has a CAN High and a CAN Low pinout. Id there a pinout diagram for the CAN-OBD2 module from Autosportlabs?
PostForum: RaceCapture/Pro General Q&A   Posted: Wed Nov 12, 2014 9:43 pm   Subject: OBDII via bluetooth?

Will there be a CAN adapter that doesn't require an OBD-II port? My ECU talks CAN, but doesn't have an OBD port.
PostForum: Hardware and Installation   Posted: Thu May 22, 2014 6:44 pm   Subject: Multiple Issues - maybe self inflicted...

Not using a tachx board, just a feed straight into the RCP. It's a digital feed from the ECU so shouldn't need any additional modules (hopefully).

I've read other peoe have used the trigger wire fr ...
PostForum: Lua Scripting   Posted: Thu May 22, 2014 12:03 pm   Subject: Development/prototype environment for testing Lua scripts?

I too would like this functionality Very Happy
PostForum: Hardware and Installation   Posted: Thu May 22, 2014 12:00 pm   Subject: Multiple Issues - maybe self inflicted...

Well, my experience of the RCP is not going too well, and I'm seeking some reassurance that it is worth persevering.

Long story short, I've had to flash the firmware 3 times and reinstall the bootl ...
PostForum: Hardware and Installation   Posted: Thu Mar 20, 2014 9:00 pm   Subject: Analogue Inputs Messed Up

I connected to my ecu and have identified that the tach out from the ecu is 2 pulses per rev, which is nice. But neither my rev counter, or the rcp are reading any revs. Could it be that the output fr ...
PostForum: Hardware and Installation   Posted: Fri Mar 14, 2014 9:28 am   Subject: Analogue Inputs Messed Up

I finally got round to installing my RCP, and have only a few requirements until the CAN adapter is sorted:

1. Get the RCP to turn on my GoPro when it detects voltage on an input
2. Read a pulsed ...
PostForum: RaceCapture/Pro General Q&A   Posted: Mon Mar 03, 2014 10:22 am   Subject: CAN bus & ECU support plans

Sounds good. Let me know when you have something you want to test. I think I mentioned elsewhere, but the Syvecs CAN output is quite flexible, so could be a good testing ground.

Very Happy
 
Page 1 of 2 Goto page 1, 2  Next
All times are GMT