Search found 44 matches
- Fri Feb 05, 2016 3:02 am
- Forum: Lua Scripting
- Topic: Serial telemetry streaming via LUA or BT spoof. Fast enough?
- Replies: 19
- Views: 14761
BT connection trigger
Could you point me to the trigger that starts the BT connection? I have managed to sometimes get my esp module to get the AT command and spoof the BT telemetry. However, the NodeMCU code of the module prints out a bunch of stuff on boot, which the RCP is interpretting as non "OK" messages ...
- Fri Feb 05, 2016 3:00 am
- Forum: RaceCapture App Operation and General Q&A
- Topic: analog channel 8-battery
- Replies: 6
- Views: 5398
Lots of info! Thank you very much, I'll try to go through all of this and eliminate all possible issues. The 5v bike reference i was refering to was just that my harness diagram shows a spot for 5v reference, however they have no wire connected to it. It made me think there might be somewhere else o...
I would also like to know. When you guys connect what should be a stable input (aka throttle position 0), do you get voltage fluctuations in the RCP data? When I connect my voltage meter the value looks pretty stable, but when reading through RCP even TPS 0 or TPS 100 has +/- 0.1 V fluctuations. Is ...
5V reference
So I just realized the purpose of the 5V reference: 5V Voltage Reference This output provides a 5V reference to be used with the Analog Inputs. Up to 50mA is provided to supply power to active sensors, pull-up resistors and other purposes. This reference output is protected against short-circuits wi...
- Fri Jan 22, 2016 8:07 am
- Forum: RaceCapture/Pro General Q&A
- Topic: CAN Bus Questions
- Replies: 7
- Views: 7249
I2C
I noticed there was no reply regarding the I2C interface. I'm also interested in trying I2C for temperature arrays. I know there are LUA modules for I2C (which I've found on the NodeMCU), but can't figure out if the RCP has that built in, i'm guessing not. For now I was going to use I2C to set my te...
K-line
Any information on how I would be able to read from a custom k-line, not full obd2.
Would it be doable through lua scripting and reading a digital input?
Would it be doable through lua scripting and reading a digital input?
How many sample points did you take? I will be able to see this from the config file. Also... I don't suppose that the voltage values shift with the engine running. Have you tried just to eliminate engine ground noise as your culprit? I took just min and max, and then capped the values at 0 for any...
I'm having trouble getting a readable PDF at the limit of ~200kb so I'm going to post a dropbox link to the full harness schematic. Sorry but eventually this link will stop working (whenever i clean up my dropbox public folder in a month/year/who knows when) https://dl.dropboxusercontent.com/u/17651...
TPS data
I need help trouble shooting. Please look at lap 451 and 454, included in the link. https://www.race-capture.com/events/tsukuba-2016-1-11/device/pmt-racing-logger?laps[]=450&laps[]=453 (Need to rescale the graphs for them because I sent the wrong min/max during streaming) I setup SusTravelF, Sus...
- Thu Dec 24, 2015 2:49 am
- Forum: Lua Scripting
- Topic: Serial telemetry streaming via LUA or BT spoof. Fast enough?
- Replies: 19
- Views: 14761
I still have a long road ahead to connect my analog sensors on the bike but i'll try to document it and let you guys know of anything that might help your product :). I have however run into another hurdle. I commented here: https://github.com/autosportlabs/RaceCapture-Pro_firmware/issues/165 So wha...