the temperature input can be added to the V3 quite easily. I have it on both of mine although I havn't used it on either yet.
Have a read through this whole thread for info
http://www.autosportlabs.org/viewtopic.php?t=2100
Col
Search found 178 matches
- Mon Oct 26, 2009 9:25 am
- Forum: Q&A
- Topic: Cooling fan control
- Replies: 20
- Views: 37381
- Wed Sep 09, 2009 8:31 pm
- Forum: Assembly
- Topic: V3 boards, processor unavailable?
- Replies: 6
- Views: 15804
Brent,
Is there a pin for pin SMT (SOIC) device that I could use with a DIP adaptor board?
Is this the one?
http://uk.farnell.com/jsp/search/altsSu ... ku=4133055
Col
Is there a pin for pin SMT (SOIC) device that I could use with a DIP adaptor board?
Is this the one?
http://uk.farnell.com/jsp/search/altsSu ... ku=4133055
Col
- Tue Sep 08, 2009 4:33 pm
- Forum: Future Upgrades
- Topic: V3.3.0 firmware / configuration software - for V3 hardware
- Replies: 90
- Views: 213370
- Wed Sep 02, 2009 7:23 am
- Forum: Future Upgrades
- Topic: V3.3.0 firmware / configuration software - for V3 hardware
- Replies: 90
- Views: 213370
Repeated the hardware updates on my other V3 unit, but this time I've sorted an input... a 3.5mm stereo jack plug which will allow me 3 seperate inputs if needed and enough board to do more hardware within the MJLJ case. Should have this little lot on trial in my Capri in the next few weeks... http:...
- Wed Aug 19, 2009 1:59 pm
- Forum: Future Upgrades
- Topic: V3.3.0 firmware / configuration software - for V3 hardware
- Replies: 90
- Views: 213370
I've been following this quite closely as I intend to use a temperature input on the Aux circuitry. Heres how I've done the internal mods so far: As I'm using a MAP optioned V3 unit, to get the Vref pin enabled on the Molex for Map switching etc., simply wire link L1. This allows the 5V and 0V for t...
- Fri Apr 24, 2009 6:10 pm
- Forum: Q&A
- Topic: Case for V3
- Replies: 6
- Views: 6379
Cheers Brent. Won't be able to see the engraving under the dash :( Once again. Many many thanks. The car it'll end up in: http://i105.photobucket.com/albums/m227/capri_turbo/tt/tt_out_3.jpg http://i105.photobucket.com/albums/m227/capri_turbo/tt/tt_out_1.jpg 2.8injection turbo (Turbo Technics). http:...
- Wed Apr 22, 2009 8:04 pm
- Forum: Q&A
- Topic: Case for V3
- Replies: 6
- Views: 6379
Case for V3
Managed to get myself a V3 bare board and processor last week... can anyone advise a case to use, or can anyone in teh UK supply the original type?
- Sat Apr 11, 2009 7:41 am
- Forum: Q&A
- Topic: V3 bare board and processor
- Replies: 2
- Views: 3947
V3 bare board and processor
Is anyone able to supply me with a bare V3 board and processor?
- Thu Jun 26, 2008 8:52 pm
- Forum: Assembly
- Topic: Surface Mount PCB construction
- Replies: 6
- Views: 8227
I'm with steve c on this one. We do a huge amount of surface mount at work. Most is on the pick and place machine, but a lot is hand placed onto pasted for reflow, and the stuff that isn't, is done by tinning one pad, reflowing with the iron to locate one end of the component and then soldering the ...
- Mon May 12, 2008 8:13 pm
- Forum: Installation
- Topic: trigger wheel on a Pinto pulley?
- Replies: 5
- Views: 13015
- Fri May 09, 2008 8:01 pm
- Forum: Operation
- Topic: serial adaptorspcmcia, not usb
- Replies: 2
- Views: 2880
serial adaptorspcmcia, not usb
anyone have experience with these? My new laptop has no rs232 port and my usb to 232 adaptor won't install at all, so i'm looking at pcmcia adaptors.
Col
Col
You might be able to open it up and salvage the MAP sensor though. don't think so, Ford map sensors normally produce a frequency not a voltage standard ford map sensors use a similar freescale unit to that of the MJLJ, BUT it is the non ported type and is sealed in the ford unit. There is also a PI...
- Fri Apr 18, 2008 8:19 pm
- Forum: Assembly
- Topic: crimping junior mini-fit pins
- Replies: 11
- Views: 22394
for Molex terminals, you ideally need the correct Molex crimp tool... not cheap at upto £200+ (not joking, just bought a small one for a job at work). I'm quite lucky working in the electronics industry that I had access to the correct tools. Other cheaper tools may well do the job well enough, but ...
- Fri Apr 18, 2008 8:11 pm
- Forum: Operation
- Topic: MOLEY MOLEY MOLEX plug!!
- Replies: 3
- Views: 3344
- Mon Oct 22, 2007 8:59 pm
- Forum: Powered by Megajolt Gallery
- Topic: Supercharged Pinto Capri with MEGAJOLT!!!
- Replies: 9
- Views: 14958
nice on Nat. Great to see another Capri running MJLJ. Ican't take the full credit for the coil pack on dizzy... i got the idea from someone else on here lol. I did a load of tuning on mine over the weekend and improved bottom eng torque and engine acceleration. Mine is going so much better than it e...