Search found 35 matches
- Thu Apr 17, 2014 11:27 pm
- Forum: General Discussion
- Topic: Shipping Charges.
- Replies: 3
- Views: 5668
Shipping Charges.
Are these correct? I'm looking at buying a Hard Cut rev limiter board. $25.95. ( Works out at about £15.45 ) Postage. A whopping $43.50. That's getting on for twice the price of the board! I'm sure that the last time I purchased from the site, the postal charges were FAR more reasonable. Is this a g...
- Tue Dec 14, 2010 2:32 am
- Forum: Installation
- Topic: Aux input on a switch. Mj lt V4.
- Replies: 8
- Views: 6007
- Mon Dec 13, 2010 9:49 pm
- Forum: Installation
- Topic: Aux input on a switch. Mj lt V4.
- Replies: 8
- Views: 6007
Erm.. I thought the only change needed was cutting the track at R8? (From memory.. Haven't checked..) This was where I was going to wire in the switch. I had looked at the possability of the TPS input. But my Megajolt uses MAP. I do have a second MJ unit that currently has TPS, but I intend on conve...
- Mon Dec 13, 2010 9:06 pm
- Forum: Installation
- Topic: Aux input on a switch. Mj lt V4.
- Replies: 8
- Views: 6007
- Mon Dec 13, 2010 8:52 pm
- Forum: Installation
- Topic: Aux input on a switch. Mj lt V4.
- Replies: 8
- Views: 6007
Yes, I understand. Basically, I'd need to change the calibration information every time I changed the switch. It was more a 'can it be done' than 'is it practical'. :) I'd certainly like to try both water temp and Lambda readings on the MJ JR V4 unit. Atleast I can try both, and see if one works bet...
- Thu Dec 09, 2010 2:15 pm
- Forum: Installation
- Topic: Aux input on a switch. Mj lt V4.
- Replies: 8
- Views: 6007
Aux input on a switch. Mj lt V4.
Quick question. I'm running a Megajolt V4 on a Zetec running a carb. I have an engine temp gauge and a Lamda sensor. The Lamda outputs 0-5v, so obviously I can't just switch from one to the other without disabling the resistor on the board. My question.. Would there be any issues with installing a s...
- Sun Dec 27, 2009 1:10 am
- Forum: Ignition Map Library
- Topic: Looking for a map for a Zetec on a single carb.
- Replies: 3
- Views: 6558
Yes, it does actually work quite well on the standard map. I've actually had a read of an ignition book and modified the base map using some information within that. I've just not had a chance to try it yet. Can anyone point me in the direction of making my own map? Information regarding how load an...
- Wed Dec 09, 2009 6:31 pm
- Forum: Installation
- Topic: Why does our rev counter work
- Replies: 2
- Views: 4226
- Wed Dec 09, 2009 6:19 pm
- Forum: Installation
- Topic: rev counter
- Replies: 9
- Views: 7465
I don't suspose anyone has any information on getting a rev counter working on a Mk2 Fiesta? My gauge used to work on the old CVH I had in. I've been told that the Megajolt feed doesn't work on these, so I got the Zeners and tried it that way. This works very intermittintly. Now either, my gauge is ...
- Mon Nov 23, 2009 6:53 pm
- Forum: Ignition Map Library
- Topic: Looking for a map for a Zetec on a single carb.
- Replies: 3
- Views: 6558
Looking for a map for a Zetec on a single carb.
As title.
I'm after a V4 map for a 1.8 Zetec running a 34 DMTR carburettor.
Or something similar.
Jason.
I'm after a V4 map for a 1.8 Zetec running a 34 DMTR carburettor.
Or something similar.
Jason.
- Sun Sep 13, 2009 12:44 am
- Forum: Installation
- Topic: EDIS connections....
- Replies: 10
- Views: 10143
- Sun Sep 13, 2009 12:38 am
- Forum: Installation
- Topic: Cable suppliers UK.
- Replies: 9
- Views: 6233
- Sat Aug 08, 2009 8:42 pm
- Forum: Installation
- Topic: Cable suppliers UK.
- Replies: 9
- Views: 6233
That's not thick enough is it? (Not a high enough AWG rating.)NITROPIXIE wrote:Something like these should be fine. I think the single core should be fine.
http://www.maplin.co.uk/Search.aspx?menuno=13093
The single core stuff works out more expensive than TriggerWheels.
Jason.
- Sat Aug 08, 2009 4:33 pm
- Forum: Installation
- Topic: Cable suppliers UK.
- Replies: 9
- Views: 6233
- Sat Aug 08, 2009 12:50 pm
- Forum: Installation
- Topic: Cable suppliers UK.
- Replies: 9
- Views: 6233