Search found 219 matches

by Dean924s
Tue Nov 11, 2008 6:52 pm
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

alexander, Thanks for the info. I had read most of that but not all. Really good info!!!. My biggest worry is getting the wheel mounted up and centered properly as it looks like the RX7 VR units need to be much closer to center than the Ford ones. I may have to mount it up and then true it with a ru...
by Dean924s
Tue Nov 11, 2008 2:35 am
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

Ok I have found a source for 72 tooth gears unfortunately it is only 3" in diameter but I will have to go get a Mazda vr sensor (I know where one is in the junk yard.) It was listed in stock and shipping tomorow. I hope I see it before the weekend. "6325K67 Steel Plain Bore 14-1/2 Deg Spur Gear 24 P...
by Dean924s
Tue Nov 11, 2008 2:02 am
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

Ok This is what I was wanting to get.. . I have some serious thinking to do. Anyone have a 72-2 wheel around? I guess I could make up one by drilling holes in a spare cam wheel. I think I had better get a 72-2 wheel mounted up just in case. The rest of the bits are easily obtainable from the local w...
by Dean924s
Mon Nov 10, 2008 11:05 pm
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

And a couple more of other things - Sensor mounting location and tdc on the cam. The nice thing about cam mounting is you can not be 180 out.

Also a mockup of the wheel in place. getting the alignment corect for mounting the wheel to a spair cam gear I have shown in the previous posts.
by Dean924s
Mon Nov 10, 2008 10:56 pm
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

Some of the motor showing the cam mounted cap and rotor.
by Dean924s
Mon Nov 10, 2008 10:52 pm
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

An update with some photos of the wheel mounted to the cam gear.
by Dean924s
Sun Nov 09, 2008 5:46 pm
Forum: Installation
Topic: 72-2 Toothed Wheel
Replies: 24
Views: 28043

Bump ! Does anyone know ? 'But - since the wheel is 72-2 toothed. Should the sensor be mounted at half the degree BTDC that you would have on a 36-1 wheel ? Since 1 revolution of the distributor axis equals 2 revolutions on the crank.' I am going to try to reason my way through this question. My fi...
by Dean924s
Sat Nov 08, 2008 8:24 am
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

Brent, Thanks for the reply. I had read all of what you noted in your post. I have been lurking here for a very long time. I guess the really short question is would this work with the following set up. EDIS8 with four coils one per plug on a 4 cylinder motor getting signal from a 36-1 on the cam by...
by Dean924s
Sat Nov 08, 2008 4:48 am
Forum: Powered by Megajolt Gallery
Topic: COP 4 cylinder - 924s/944 & other content - Very Long Po
Replies: 137
Views: 161488

COP 4 cylinder - 924s/944 & other content - Very Long Po

EDIT: 2008-12-07 For those that are looking at going down this road (and have never done it before) I strongly suggest installing a "standard" EDIS based system first. There are many possible things to try / change but first and foremost you want your car to be up and running. When I got started wi...