Not writing logs or sending telemetry data

raydoc · Post by **raydoc** » Sun Aug 04, 2013 4:18 pm

All the lights seems to flash correctly. I have it set for CSV file. T-Mobile SIM installed and lights seem to flash happily.

Ideas? When I log in on-line there is no session to look at as the instructions say there should be.

rdoherty · Post by **rdoherty** » Mon Aug 05, 2013 3:13 am

Hi raydoc, did you add the device id to the configuration and apply it to your RaceCapture device?

raydoc · Post by **raydoc** » Mon Aug 05, 2013 3:30 am

rdoherty · Post by **rdoherty** » Mon Aug 05, 2013 3:23 pm

What's the email address you used when creating an account on race-capture.com? I can take a look.

Also, can you upload your Race Analyzer config? Thanks!

raydoc · Post by **raydoc** » Tue Aug 06, 2013 2:22 am

The email account is [email protected]

I'll have to get a team mate to download the setup but it looks just like the wiki but with our device ID typed in.

rdoherty · Post by **rdoherty** » Tue Aug 06, 2013 2:52 am

Ok, I checked the website and your device hasn't connected or sent any data. Can you tell me what speed the middle LED blinks at? Different speeds mean different things:

http://www.autosportlabs.net/RaceCaptur ... metry_LEDs

raydoc · Post by **raydoc** » Tue Aug 06, 2013 2:56 am

Slow blink, maybe one in three seconds. Left two vertical LEDS flash dimmly but quickly.

Post by **brentp** » Tue Aug 06, 2013 4:59 am

Hi Ray,

It would be good to check your RaceCapture/Pro config file. we want to make sure you're not setting a logging rate that's too high - it would overwhelm the connection.

Also, are you powered via USB only or hard wired to the car? When transmitting via telemetry, USB alone does not provide enough power.

raydoc · Post by **raydoc** » Tue Aug 06, 2013 10:12 am

I believe that all settings are like the examples for rate. How to download the configure file to post?

Post by **brentp** » Tue Aug 06, 2013 2:49 pm

Read your config file from RaceCapture/Pro and then do a 'save configuration as'. You should be able to attach it to a post here.

raydoc · Post by **raydoc** » Tue Aug 06, 2013 5:53 pm

Config file. The board would not accept the rcap file type so I changed it to txt. Hope it works.

Is there a way to email you the file directly?

Post by **brentp** » Tue Aug 06, 2013 6:21 pm

Thanks.

You have your accelerometer and yaw settings set to 30Hz. try reducing that down to 5-10Hz per channel.

Also, you able to log to the SD card, correct?

regards,

raydoc · Post by **raydoc** » Tue Aug 06, 2013 8:17 pm

Yes. Can log to SD. I'll turn them down to 10hz.

smig · Post by **smig** » Sat Aug 10, 2013 3:37 am

Hi Ray,
did you enter the Telemetry Device ID that is generated when you register your Realtime device on www.race-capture.com? If I'm reading it correctly, it's blank in your configuration:

"outputConfig" : {
"sdLoggingMode" : 1,
"telemetryMode" : 0,
"telemetryServer" : "54.245.229.2",
"telemetryDeviceId" : "",
"p2pDestAddrHigh" : 0,
"p2pDestAddrLow" : 65535
},

raydoc · Post by **raydoc** » Sat Aug 10, 2013 11:09 am

Several times. I even created a new one. It is connecting to t mobile but not working with your server. I am at NJMP with Lemons this weekend.