Search found 9 matches

by Tadhg
Fri Mar 13, 2015 4:22 am
Forum: Q&A
Topic: Troubleshooting - No Spark
Replies: 1
Views: 2296

Troubleshooting - No Spark

Hello all. I've got an MJLJ (v4) running in my Mini. Or at least, it was, for about 18 months. This week, it's decided not to work anymore. It's running an EDIS (obviously!) and a standard Motorcraft Ford 4 cylinder coil pack. And a Ford VR sensor. When it died, I thought it'd run out of fuel. That'...
by Tadhg
Fri Jan 04, 2013 5:47 am
Forum: Operation
Topic: Auxiliary Voltage Tables
Replies: 1
Views: 2512

Ok - figured out my problem. My problem is that I used the Fahrenheit scale. I used it in order to avoid using negative numbers. Thankfully, after checking everything, my lowest Celsius number is 1. The Auxiliary Input Table won't accept values higher than 255. This is the reason why my last 5 value...
by Tadhg
Thu Jan 03, 2013 9:34 am
Forum: Operation
Topic: Auxiliary Voltage Tables
Replies: 1
Views: 2512

Auxiliary Voltage Tables

Hello all. Got a quick question with regards to the Voltage Tables for the Auxiliary Input. I'm using my Auxiliary Input to monitor coolant temp, I've gone and measured the temp of the head at the thermostat to get a few points, then interpolated and extrapolated them to get the following series of ...
by Tadhg
Thu Jan 03, 2013 8:18 am
Forum: Installation
Topic: Tacho, Revs, PIP and SAW
Replies: 4
Views: 4993

Update - vehicle's running. :) Running beautifully. 8) I did manage to mix up six of the wires total in the installation - obviously PIP and SAW, plus the VR wires, and then I mixed up EDIS 10 and 12 at the coilpack. None of the wiring colours matched what I had. No drama, no damage done, all runnin...
by Tadhg
Sun Dec 09, 2012 2:03 am
Forum: Installation
Topic: Tacho, Revs, PIP and SAW
Replies: 4
Views: 4993

Ok, problem solved. Both PIP/SAW and the VR Wires were crossed. So, my description of PIP is that it gives off an output that will light an LED test light (+12V), whilst SAW won't light an LED test light. Regardless of polarity. The VR wires are only giving off about +1.5V (DC) on the choke (about 1...
by Tadhg
Sun Dec 02, 2012 11:37 am
Forum: Installation
Topic: Tacho, Revs, PIP and SAW
Replies: 4
Views: 4993

Hi Brent, been on holidays since the day you posted, only back tonight. Hope to get at it in the next couple of days...
by Tadhg
Wed Nov 21, 2012 8:51 am
Forum: Installation
Topic: Tacho, Revs, PIP and SAW
Replies: 4
Views: 4993

Tacho, Revs, PIP and SAW

Hello all. I've a Mini in which I'm trying to install an MJLJ v4. I've wired everything up, but haven't yet switched from the dissy and coil to the coilpack. I'm still, effectively, testing. It's only been about a month. :oops: I've managed to get the MJLJ communicating with my laptop. I can read MA...
by Tadhg
Sun Sep 23, 2012 8:32 am
Forum: Future Upgrades
Topic: Megajolt LCD display
Replies: 35
Views: 47552

That all sounds pretty cool Spockie. I've got a Mini (Aussie delivered, so definitely pre-96/OBD/OBD II - didn't notice I hadn't listed my location before) with a kit half installed (trigger wheel and hall effect sensor installed, no electrics installed/connected yet - car's' still running a dissy),...
by Tadhg
Sat Aug 25, 2012 11:17 am
Forum: Future Upgrades
Topic: Megajolt LCD display
Replies: 35
Views: 47552

Thread revival! It's been two years since this concept was first raised, has anyone had any success with this idea yet? :)