Search found 9 matches

by o07wray
Sun May 12, 2019 12:36 pm
Forum: Ignition Map Library
Topic: Chevy 2.2 4cly
Replies: 0
Views: 3159

Chevy 2.2 4cly

I have a Chevy s-10 1996 inline 4cly 2.2L... wasted spark. Does anyone have a map for this ?

THANKS IN ADVANCE!
by o07wray
Fri Apr 27, 2018 1:36 am
Forum: Installation
Topic: need pinout for Megajolt E1
Replies: 1
Views: 2460

need pinout for Megajolt E1

The molex connector on my MJ E was removed and lost ! Need Saw, pip 12v+ and Neg. The vehicle install guide only shows Pip & saw going to MJLjr and no pinout. It used to be here and I have used it, but its been several years and I can even find a manual for MegaJolt-E!

Please help!
Jeff
by o07wray
Tue Nov 26, 2013 7:15 pm
Forum: Installation
Topic: tests for the 4-edis module
Replies: 6
Views: 5208

Thanks again. BMC

But I really want to know the signal should be like. So I can drag out the O-scope and test the EDIS module.


Anyone ??
by o07wray
Mon Nov 25, 2013 6:24 am
Forum: Installation
Topic: tests for the 4-edis module
Replies: 6
Views: 5208

bmc, I don't have a wire hooked up to pin #2 on the EDIS... And if your speaking of the coil, pin #2 is 12v+ pin1 is 1&4cly coil.. and pin3 is 2&3cly coil.. I have a bare minimum install like this: http://i686.photobucket.com/albums/vv224/o07wray/edis4.jpg what I need to know is what kind if signal ...
by o07wray
Mon Nov 25, 2013 3:22 am
Forum: Installation
Topic: tests for the 4-edis module
Replies: 6
Views: 5208

well what is the EDIS voltage or signal at the pin numbers 10 & 12? is it a 12v+ that stays at 12v+ until it goes Neg and fires the coil.. or is it a 5v+ that rises to 12v+ and fires the coil.. or a open circuit until the EDIS closes and connects it to ground ( like a switch )? I understand how a co...
by o07wray
Sat Nov 23, 2013 8:48 pm
Forum: Operation
Topic: Delay spark after set number of revs
Replies: 3
Views: 3261

yep tried that first....
by o07wray
Sat Nov 23, 2013 8:02 pm
Forum: Installation
Topic: tests for the 4-edis module
Replies: 6
Views: 5208

tests for the 4-edis module

Looking for some info on the signals I should see at the coil output...a and b.. at cranking.. is it a Neg pulse to fire the coils? I know this is a dumb question, but My install was up and running great,, about 20hrs,, and then it quit firing on 2 cly. ( one side of the coil ) and rather than remov...
by o07wray
Sat Nov 23, 2013 6:05 pm
Forum: Future Upgrades
Topic: START DELAY TILL' SPEC RPM
Replies: 1
Views: 4502

START DELAY TILL' SPEC RPM

My MJjr has only one issue,, it fires instantly.. kicking back against the starter... Even before the engine has made 1 full rev the coil has fired!! My suggestion: A set number of rev's before MJjr fires or a fixed/adjustable min rpm before it fires.. I thought about installing a NC push button swi...
by o07wray
Tue Sep 03, 2013 4:02 am
Forum: Operation
Topic: Delay spark after set number of revs
Replies: 3
Views: 3261

Delay spark after set number of revs

I have a Megajolt/e and love it ... but when I start my 4cly , it fires on the first rev ( or even part of a rev ) and kicks back against the starter.. HARD,, I would like to delay the spark for a few revoulitons before it fires the coils,,,

Thanks in advance ( yup,, I know,, sick punn..)

Jeff