Search found 13 matches

by petik
Fri Mar 29, 2019 1:58 am
Forum: RaceCapture App Operation and General Q&A
Topic: Not getting lap times into podium
Replies: 5
Views: 1521

Hi Pete, Spotted your problem. In your Setup you have "Race Timing" turned off. Try turning it on, under Setup / Race Timing, then write the settings back to RaceCapture. Let us know if that works for you. Before your next event, you should be able to create a simulated track in a parking lot or ro...
by petik
Fri Mar 22, 2019 5:13 pm
Forum: RaceCapture App Operation and General Q&A
Topic: Not getting lap times into podium
Replies: 5
Views: 1521

ferg wrote:Have you made sure the correct track is loaded? Do you have the "Automatic Track Detection" turned on under "Race Tracks"?
Yeah it's got the right track. I can see the car on the track in podium. I can even see predictive timing, just not actual lap times.
by petik
Fri Mar 22, 2019 3:27 pm
Forum: RaceCapture App Operation and General Q&A
Topic: Not getting lap times into podium
Replies: 5
Views: 1521

Not getting lap times into podium

Weird thing started happening on my rct2 with podium. I no longer get lap times pushed to it or shown on the tablet. However all other telemetry is being pushed including GPS location. Any ideas? Only change I can think of that I made is upgrading app and firmware to latest. Event: https://podium.li...
by petik
Mon Mar 18, 2019 1:21 am
Forum: OBDII PIDs discussion
Topic: Import Ford PIDs into RaceCapture
Replies: 15
Views: 7715

Bump on this, also very interested in seeing this writeup - particularly for early 2000s Fords as the op asked.
by petik
Thu Mar 14, 2019 1:45 am
Forum: AnalogX
Topic: Pull-up jumpers
Replies: 3
Views: 1258

Hi, Those pads are for jumpering to enable a 2.2K pull-up resistor that is already on-board. You do not need to solder a 2.2K resistor in that place. Normally the jumper is open; to enable the resistor, solder across the joint. Also please make note of the possible limitations using thermistor-base...
by petik
Mon Mar 04, 2019 3:04 am
Forum: AnalogX
Topic: Pull-up jumpers
Replies: 3
Views: 1258

Pull-up jumpers

Just got my analogx recently and i'm wiring up an oil temp gauge. Looks like there are pads on the back of the pcb to solder down a 2.2k. What I wanted to clarify is how the wiring should look like at this point if the 2.2k is on board. Does that mean that I only connect the ground and the input and...
by petik
Fri Jul 06, 2018 4:07 pm
Forum: ShiftX2
Topic: ShiftX with /Track
Replies: 7
Views: 3774

RaceCapture/Track MK2 with it's dual CAN bus can work with ShiftX2 using an RJ45 splitter; that way OBDII data can be accessed on CAN bus 1, and ShiftX2 can be controlled on CAN bus 2. A splitter like this would do the job. The OBDII cable would plug into one of the ports, ShiftX2 in the other port...
by petik
Fri Jul 06, 2018 2:55 pm
Forum: ShiftX2
Topic: ShiftX with /Track
Replies: 7
Views: 3774

RaceCapture/Track MK1 does not support Lua scripting, which is currently needed to control ShiftX2. The new RaceCapture/Track MK2 currently on pre-order does support Lua scripting, and can work with ShiftX2. Thanks - Hope that clarifies things! Brent, will it also work when using the Legacy adapter...
by petik
Thu Jan 11, 2018 2:39 am
Forum: RaceCapture/Track Installation
Topic: E46 M3 CAN bus setup
Replies: 6
Views: 3562

Here's a video of the gauge view https://www.youtube.com/watch?v=goBiHH911vw The response is about as good as it is on my tablet. The menu navigation is more sluggish, but definitely usable. I did notice that some of the PIDs don't work so i'll have to mess with that. Clutch and brake don't register...
by petik
Wed Jan 10, 2018 7:44 pm
Forum: RaceCapture/Track Installation
Topic: E46 M3 CAN bus setup
Replies: 6
Views: 3562

This is the deck: https://www.eonon.com/Android-Car-GPS/Vehicle-Specific-GPS/BMW-E46-Android-71-Octa-Core-2GB-RAM-Car-Radio-GPS-Navigation-System-7-Inch-1-Din-Multimedia-Car-DVD-CD-Player.html except i have one generation older (only runs android 6) It seems to run ok, but I haven't had it out to th...
by petik
Mon Jan 08, 2018 1:53 am
Forum: RaceCapture/Track Installation
Topic: E46 M3 CAN bus setup
Replies: 6
Views: 3562

Just for point of interest, I am using an aftermarket android deck in my e46 which is able to run the racecapture app. Makes the integration really clean - no phone or tablet necessary.
by petik
Mon Jan 08, 2018 1:52 am
Forum: RaceCapture/Track Installation
Topic: E46 M3 CAN bus setup
Replies: 6
Views: 3562

Success! The issue ended up being that there are two twisted pair wires in the ECU wiring bundle that are color coded exactly the same. Only one of them is correct though.

In the attached photo, the positaps on the right are correct, while the disconnected positaps on the left are the wrong pair.
by petik
Sun Jan 07, 2018 9:29 pm
Forum: RaceCapture/Track Installation
Topic: E46 M3 CAN bus setup
Replies: 6
Views: 3562

E46 M3 CAN bus setup

Hoping someone that's got the track logger running on an e46 can chime in. I'm trying to get set set up on an 04 E46 M3 but seem to be failing. I wired up an ethernet cable per instructions here: https://wiki.autosportlabs.com/BMW_E46_CAN I used positaps to hook everything up. The unit powers up fin...